How to glue wallpaper in the corner of a room. How beautiful it is to join different types of wallpaper in the corners, especially if they are uneven. Features of gluing meter wallpaper
The most difficult task in pasting wallpaper is pasting the corners (outer and inner). There are two ways to carry out the process: in a joint at a corner or with wallpaper at a corner. dock them need to carefully to avoid defects.
For easy docking of wallpaper in the corners, it is necessary take clear measurements distance to the corner to determine the flatness of the surface and the corner. It is best to hide the unevenness in the inner corner than in the outer one.
After leveling the walls without the use of special perforated corners, a situation may arise when, during wallpapering, a person encounters uneven corners.
This situation can cause inexperienced builders difficulty in moving forward.
To prevent this from happening, it is necessary to remember the methods and features of pasting wallpaper in the corners premises:
- Initially needed put glue on the corner wall for wallpaper. This is done for better adhesion of the wallpaper to the wall;
- It is not recommended to glue a single piece of wallpaper on the corner, as bumps, bends, bubbles, folds may appear, which can lead to damage to the canvas. Therefore, you need to glue the corners, overlapping two pieces;
- Doing wall measurements, on which you need to stick a strip for docking on the corner, and transfer them to the strip. Then cut off the desired piece;
- We generously lubricate the wall with a second layer of glue and put wallpaper on the wall. We smooth it with a foam roller in the direction from the wall to the corner. We also smooth out the overlap around the corner;
- After that, on the other side of the corner glue the next strip, aligning a pattern or pattern.
Wallpaper pasting has always been accompanied by the problem of joining wallpaper strips in such a way that not to be seen. This can be achieved by experienced craftsmen who have pasted over more than one object with wallpaper. If this process is occupied by a person who does not have much experience, you need to somehow get out of the situation.
Docking wallpaper is the most difficult task in the whole process. This is not overlapping pasting, in which it is enough just to apply the next strip evenly. Difficulty in joining lane to lane arises on uneven surfaces, or in the case of an uneven start line.
To properly dock the wallpaper, necessary:
- cook essential tool(sharp clerical knife, long straight ruler or level, pencil and tape measure);
- On the wall glued the first strip wallpaper;
- Then the second strip is glued with a small overlap of 2 cm;
- After that, we take a ruler or a long level and put on the wall on the resulting overlap;
- Doing pencil marks at the interface;
- After measuring the evenness of the marks, you can proceed to cutting wallpaper along the line of marks;
- Next, the surface is smeared with glue, and the edges of the wallpaper are joined, as a result of which get a smooth seam.
When pasting wallpaper occurs the need to cut them in some places. For this process, it is necessary to glue the first canvas, and then overlap with the second canvas, 10 cm wide.
After that, a plumb line is taken, it is applied to the wall and piece is cut clearly on it. As a result of such actions, an overlap of no more than 6 cm should be obtained.
The place that has formed is cut off with a sharp a utility knife with a thin blade. To get an even cut, you can use a plumb line and a ruler. The intensity of pressing the knife when cutting the wallpaper at the corner should be sufficient to cut both layers of wallpaper at a time.
By carrying out this operation, there may be difficulty in gusts of wallpaper in the path of the blade. Here you need to return the knife back a little, then make an incision in a weak area, and continue trimming to the bottom. If the wallpaper continues to tear, then you need to wait a bit for them to dry.
After finishing the cut, you must carefully peel off the top layer from the cut and remove it. After that, the top layer joins with the bottom even seam in the corner of the room.
In the same way, you can glue the outer corners, only in this case you need to be especially careful, because the wallpaper should be clearly aligned, without extra protrusions.
Also watch a video with tips from the master on how to glue wallpaper in the corners
High demands are now placed on the type of interior. The owners of Khrushchev houses, who repeatedly glued paper tapestries in their apartments, now do not dare to start repairs with their own hands. They don't know how to stick wallpaper in the corners to make the room look up to par. It is more difficult to work with vinyl and non-woven fabrics. They are heavy and require certain skills. If you properly seal the corners with wallpaper, then the next repair will not be soon.
How to glue wallpaper in the corners?
Rough corners scare novice craftsmen, and even ones are a rarity.
It is difficult to bring two planes together perfectly. Therefore, even with flat walls, the corners have a lot of deviations. I had a lot of work and Vadik had to finish the aunts' apartments on his own. He did not dare to start, because he did not know how to properly glue the wallpaper in the corners.
Sticking wallpaper in the room
I decided in practice to show my friend how to wallpaper the rooms of old houses. One of my teams was renovating an apartment in a historic building. Vadik could see:
- preparation;
- alignment methods;
- how to use perforated corners;
- room decoration.
The technology for finishing corners with wallpaper of all types is the same. Only thin paper tapestries and fiberglass cobwebs can differ. Work must begin from the front door of the room when gluing end-to-end. When applying the edge of the strips of thin tapestries - from the window.
Preparation and leveling simplifies subsequent finishing
Correctly glue the wallpaper in the corners
Making repairs in old apartments, I always putty the walls and install perforated corners. They simultaneously serve as beacons and protect the ledges from destruction. I choose cardboard if the inner corners have slight irregularities. In all other cases, I use a PVC profile.
- I check the verticality of the walls with a laser level. You can use a plumb line. I choose a base more even surface.
- I putty and drown the profile in the solution, setting it in level.
- I smooth after drying with another layer of putty. Under paper and non-woven wallpaper, I use an additional finishing composition.
Related article: Wallpaper for the children's room
If customers do not want to spend money on leveling and corners, then I simply close up large depressions. I glue the corner with wallpaper, cut off a strip 10 - 12 cm wide. I place it evenly on both walls, make cuts for a snug fit. After that, it is easier to glue the wallpaper in the corners. If the upper canvas has to be cut or the paper tapestries burst, then thanks to the background of the same material, this will not be noticeable.
Self-glue wallpaper in the corners
Advice! It is better to align the corners well once than to fool your head every time you wallpaper a room.
We paste over the protrusions
The last strip in front of the corner is cut off with the expectation that it will go onto another wall by about 2 - 5 cm, depending on the curvature. The more drops, the wider the entry. It must completely cover the most convex place by at least 8 mm.
For a better fit, I make notches with a sharp knife or just cuts with scissors. It is desirable that they be inclined with respect to the edge. I close the corners with wallpaper and smooth out the main part first, then the strip around the corner.
How to glue wallpaper in the corners of the apartment?
Before starting to glue the wall from the corner, we measure the width of the trellis and draw a line vertically along the level. I check additionally the condition of the corner. The side surface of the strip should run over the deepest dent. I stick strictly vertically, according to the markup. Near the corner, the edge lies flat. The protrusions are hidden under the wallpaper pasted before.
Wallpaper with a large pattern is best cut so that the lines match. A small shift will be imperceptible.
Thick vinyl wallpaper I cut along the ruler at a distance of 2 mm from the edge of the top sheet. With a sharp knife, I cut both pieces strictly vertically along the entire height. I remove the excess and the canvases lie end-to-end. For strength, I enclose a painting grid.
When repairing an apartment with your own hands, wall decoration with wallpaper is the simplest type of work. Minor difficulties arise only when pasting hard-to-reach places: battery, window, door and corner. But if you know simple tricks, then here everything can be done quickly and with high quality. At the same time, the greatest number of secrets lies in the technology of pasting the corner. After all, it can be external and internal - hence the different solutions. To help beginner finishers in this article, we will analyze in detail how to properly glue wallpaper in the corners. For wallpapering in the corners, you will additionally need the following materials and tools (the main materials and tools for decorating walls with trellises are listed in the work ""): When wallpapering corners, it is difficult to ensure that they fit snugly against adjacent walls without wrinkles, air pockets and excessive tension. The joints of adjacent walls are to blame for this. They are either uneven, zigzag if the walls were plastered, or littered if the house is panel. Therefore, an important task is to align the corners before starting work on decorating the room with wallpaper. Professional builders have several methods for this. The most common are listed below. Method number 1. To one of the walls is strictly vertical, the control is carried out by a plumb line, a rule is closely applied, and even better - a metal profile. Thus, the most protruding point of the surface of the adjacent wall is found. An angled spatula is applied closely to the point, and a profile is applied to the spatula. Again, with the help of a plumb line, the profile is brought to a strictly vertical position, after which 3-4 marks are made on the wall for mounting the dowels. Holes for them are drilled with a perforator, after which a profile is attached to the wall with self-tapping screws. The corner is wetted with water, after which gypsum putty is applied to it. With an angled spatula, pressing against the profile, a perfectly even angle is formed. Excess plaster is removed, the procedure is repeated at the next corner. After the putty dries, it is processed with zero sandpaper. Method #2. For this method, you will need a countershultz (plaster corner), which is a metal or plastic corner with a mesh attached to the edges. It is installed in a corner strictly vertically (a plumb line or a laser level will help) and is attached to the wall with putty applied over the grid. After complete drying, the putty layer is polished with a special mesh or sandpaper. The above methods of aligning the corners allow you to solve any violations of the geometry of the joints of adjacent walls. When working with wallpaper, novice finishers will definitely meet with pasting of internal corners and, possibly, external ones. The methods of pasting them are different, regardless of whether paper, vinyl or non-woven type of trellis is used. Attention: in this section we are talking about plain wallpaper that does not require color matching. How to stick wallpaper in the corners of a room with a pattern will be discussed at the end of the work. So, how to glue wallpaper in the corners? In apartments of modern construction, there are practically no external corners that need to be pasted over. The exception is window slopes, but they are usually painted, not glued. If, nevertheless, you have to glue the outer corner, then below we will provide instructions on how to glue wallpaper in the corners of the room in this case. The step-by-step algorithm of actions is as follows: When pasting the inner corner, the last strip of wallpaper should capture the adjacent wall by 2-3 cm. To do this, it is sized in width - it is measured out, and the excess part is cut off. After gluing it, a vertical line is drawn on the strip at a distance of 4-5 mm from the corner. For this, a plumb line and a pencil are used. The next wallpaper sheet is overlapped, strictly along a vertical line. If the seam is barely visible, this completes the pasting of the corner. Otherwise, an incision is made that allows you to remove the parts of the wallpaper pasted on top of each other and form a butt seam. Note that the use of wide, meter-long wallpapers reduces the number of seams, which speeds up the entire technological process, but greatly complicates work in the corners. With a relatively small blockage of the wall, a deviation from the vertical of up to 2 cm, it is possible to join the wallpaper with a clear geometric pattern so that the seam can be found only as a result of a careful study of the pasted wall. We note right away that a shift in the pattern is possible, but very slight, and therefore hardly noticeable, if everything is done in accordance with the instructions. For reference: wallpapers with different patterns do not need to be joined. They are glued according to a simplified scheme. There is nothing complicated in the materials that answer the question of how to properly glue wallpaper in the corners of a room. You can easily do the work yourself. Every master in any field of activity always has his own little secrets. Wallpapering corners is no exception. It also has its own secrets. The technology of pasting corners with wallpaper is complicated only at first glance. Pasting the walls with wallpaper will help create a cozy homely atmosphere in the kitchen. Thanks to modern developments, this finishing material, and in particular non-woven wallpaper, can compete with plastic in strength and durability. At the same time, they are more environmentally friendly, allow air to circulate and are easier to work with. The only thing you have to tinker with is to figure out how to glue the wallpaper in the corners. Properly selected wallpaper is already half the success. Having saved on quality, you can lose a lot in durability, and you will have to do repairs again in a year or two. Non-woven wallpaper - one of the best options for the kitchen Non-woven bases are more convenient when it becomes necessary to change the wallpaper. To do this, you just need to remove the vinyl layer, and the new canvas can be glued onto the old finish. Consider what types of wallpaper are, and whether it is possible to glue the kitchen with them: Related article: Laying laminate on a parquet floor: tools, materials, workflow
In order to properly paste the wallpaper and not be caught off guard by the lack of necessary tools in the process, check that you have everything you need before repairing. You will need: Pencil - a necessary auxiliary tool for wallpapering in the corners Wallpapering is a simple matter, but it also has its own subtleties. As a rule, difficulties arise if you do not know how to glue wallpaper in the corners. When at least one corner turns out to be crooked, as the wall is glued along, there will be an increasing skew of the canvas relative to the floor surface and kitchen windows or the ceiling. You should not focus on the doorway as the starting point for wallpapering the walls. Check with a plumb line whether it is really perpendicular to the floor. It is highly likely that the frames are also installed with an error, which will lead to skew, and the corner will be swollen. The tradition of starting wall decoration with wallpaper from door and window openings originates from the need to overlap paper wallpaper so that the latter is less noticeable. With the advent of vinyl and non-woven materials, such a need has disappeared, since the canvas is glued end-to-end. Smooth corners are much easier to glue than curved corners. For large irregularities, some tricks will help Before you start working with wallpaper, it would be correct to level each corner with plaster with a building level. Minor irregularities can be dealt with with a slight overlap or by cutting off an extra piece of canvas.
A corner properly pasted over with wallpaper does not wrinkle, the edges of the canvases do not diverge, forming a gap. To achieve such a neat repair, resort to some tricks.
Russia, Moscow region, Moscow
+79041000555
It takes ~5 minutes to read
Save Another plus in favor of choosing wallpaper is the ability to independently perform simple work, getting savings and enjoying the result. However, the surface of the walls is uneven and many are stopped by the question: how to glue wallpaper in the corners? The pasted canvases repeat the unevenness of the walls, hiding some of them. But the corners are different. Even non-woven wallpaper, which is easily stretched like a fabric, when dried at uneven corners, wrinkles, folds, distortions appear. Later they peel off in these places. To prevent this from happening, you should know how to glue them correctly.
SaveCorner preparation
How to wrap corners
outdoor
Internal
How to dock wallpaper with a pattern
Other nuances of pasting corners
Related videos
Choosing the right wallpaper for the kitchen
Necessary materials and tools
Subtleties of wallpapering corners
Trimming wallpaper in the corners (video)
Wallpapering inside corners
Preparing wall corners
Even if the walls are plastered according to the beacons and puttied with high quality, this does not mean that everything is in order with the corners. Small depressions and grooves are unacceptable, they are puttied. Ideally, when puttying and subsequent sanding, the inner corner is given a minimum radius of curvature.
This will allow you to completely remove excess glue and air when pasting. When preparing the outer corner, the use of a perforated corner is mandatory. This will help create straight lines and properly wallpaper, protect the plaster from collapsing during light impacts that occur, for example, when furniture is skidded.
When applying a primer to the walls, a roller is used. For thorough priming of corners, use a brush. Choose the order in which you want to label the sheets, and decide where to start. It may be more convenient to start at the edge of a window or door opening. To begin with, choose a wall with a less visible corner, such as where a cabinet will stand.
Pick up a narrow strip of wallpaper, cut off the width of the roll. Walk with her along the selected wall, trying out options for the layout of the sheets. Choosing the option of how to properly glue the corners with wallpaper, strictly follow the rules:
- joints of sheets in the corners are unacceptable;
- no matter how even the corner may seem, do not plan to paste over it with a single sheet;
- instead of an overlap sticker, apply an overlap sticker followed by a double cut.
By shifting the starting point, choose on the wall such an arrangement of the first panel so that approximately the middle part of the next panel falls on the corner walls. Using a plumb bob and a sharpened pencil, mark a vertical line on the wall. It is not necessary to draw a solid line, which may later become noticeable.
You can make barely noticeable marks a centimeter long every 20–30 cm and draw a line not from the very junction, but, say, one centimeter to the left or right, so that later this line closes. Such an inconspicuous line will serve as a reliable guide and will not be revealed later at the junction itself, as sometimes happens.
Pasting the first sheets
Recall the sticker sequence:
- Open the wallpaper with or without pattern selection (according to the instructions on the roll).
- Apply glue to the walls, canvas, or walls and canvas (according to instructions).
- If the canvas is glued, then fold it so that the glue does not dry out prematurely.
- Stick the canvas on the wall from the ceiling down, focusing on the vertical mark or on the extreme edge of the already pasted canvas, aligning the pattern.
- Carefully remove the remaining air with a roller or brush, smoothing from the center to the edges.
- Using a wide spatula with a clerical knife, cut the top and bottom of the panel, smooth again with a roller, if necessary, grease with glue and smooth again.
Save
Save
Save
How to hang wallpaper: inner corners
- We cut out a strip from a solid panel, 5 centimeters wide than the distance from the last canvas to the corner (we measure at the ceiling, in the middle and at the floor, we take the largest), the remaining piece will be glued after the first one.
- We coat with glue (according to the instructions for the wallpaper) and paste the prepared canvas, smoothing it with a roller or brush, first on the wall, then in the corner and then a strip on the next wall, removing excess glue and air.
- In places where the wallpaper wrinkles noticeably, we make horizontal cuts 5–10 cm apart.
- Using a plumb line, we draw a vertical line to stick the remaining piece of canvas so that it overlaps by 2 cm on the previous canvas in its narrowest part.
- We coat and paste the remaining canvas, combining a smooth edge with the applied vertical line, smoothing out the remaining glue and air.
- We prepare the knife, for this, before each cut, we break off the tip of the knife along the marks on the blade.
- Using a knife and a wide spatula, we cut without separation, in one step, both layers of the canvas so that the cut runs a centimeter from the edge of the second strip.
- We remove the cut off excess, if necessary, bend the edges and smear with glue, roll with a roller.
After double trimming, an imperceptible joint remains. If it didn’t work the first time, remove the glued strips and repeat with great diligence. It will turn out for sure, and you will know how to properly paste the wallpaper in the corners.
Save
Pasting the outer corners of the room is carried out in the same order and in compliance with the same rules: we mark up so that there are no joints and do not try to paste over with a solid canvas.
After gluing the first corner piece of the canvas, the wrapped part of the wallpaper should be at least 5 cm. The next canvas should be glued according to the markup so that the overlap in the narrowest part is at least 2 centimeters. Save
Useful tips from experts
- If you find an air bubble and it does not smooth out, pierce it, remove the air, fill in a little glue with a syringe and smooth it with a roller.
- Sometimes, when cutting from above, below, or at the window and door opening, the wallpaper chews up. Let them dry a bit and cut again. Perhaps the knife has dulled and it's time to change the blade.
- Do not allow drafts in the room, this can lead to premature uneven drying and flaking of the canvases.
- De-energize the sockets and switches in the room in advance and remove the frames from them. You can return it to its place immediately after pasting.
- When gluing on problem areas, add 10% PVA glue to water when preparing the glue.
- If old wallpaper does not remove well, wet it with primer using a paint roller. Remove immediately before primer dries.
Video: how to glue wallpaper in the corners of a room