≡× MENU

• Repair
• Repair
• Interior Design
• About everything
• About plumbing

Vegetable oil, scrub and solvent will help to wash the dried mounting foam from your hands. How to wash mounting foam from hands How to wash mounting foam from hands

How to wash mounting foam from hands? - This question worries not only amateurs who have taken up repairs for the first time, but also experienced craftsmen. Some people advise generously lubricating your hands with oily cream or petroleum jelly before working with mounting foam. In such cases, the foam does not adhere well to the skin of the hands and can be easily removed in case of contact. But for sure, these people have not tried their own advice in practice, because it is very inconvenient to hold a balloon with foam and other tools with slippery greasy hands. And greasy stains from building materials are not easy to remove later. Therefore, such recommendations are very doubtful, and if the sealant gets on the skin, you just need to know how to wash off the mounting foam from your hands.

What is mounting foam?

Polyurethane foam is a sealant that is made on the basis of polyurethane. The solution is produced in aerosol packages and is widely used in construction and repair work. Its purpose is to fill gaps and cracks for effective sound, hydro and heat insulation, fastening individual parts of building materials into a single whole.

Mounting foam appeared in the construction industry relatively recently. Instead of foam, cement and tow were previously widely used, but the use of these materials took a lot of time and a lot of work. The appearance of polyurethane foam greatly simplified such work, because there is no stage of preparing the necessary substance, and additional tools are not needed at all when working with sealant.

But in the frozen state, the foam is a rigid polyurethane foam. When it comes into contact with the skin, the sealant adversely affects its cells, as it completely blocks the air flow. This building substance can provoke irritation on the skin not only of the hands, but of the whole body, as well as other manifestations of an allergic reaction. Therefore, it is very important to know how to wash mounting foam from your hands quickly without causing a detrimental problem to the epidermis.

Important! To significantly reduce the likelihood of mounting foam getting on the skin of the hands, it is necessary to work with it in personal protective equipment. Thick rubber gloves and work clothes are the best.

How to wash the mounting foam from your hands if it has not yet had time to harden?

The simplest rule in working with foam, which must always be remembered, is that the sealant must be removed immediately, as soon as it gets on the skin of the hands or on clothes.

Try to remove the contamination with a clean napkin or cloth, gently shifting the foam to the center of the stain. Residues must be washed off immediately before the composition has completely frozen.

Important! When you try to wash the mounting foam off your hands, be careful not to smear it on your skin.

If it was not possible to completely remove the foam in this way, then use one of the following aids.

Special aerosol

Before you start working with mounting foam, it is advisable to purchase a special solvent aerosol. The ideal option is the means of the same manufacturer as the foam can.

Important! You will also need a similar solvent to clean the guns with which the sealant was applied. The tool is available in the form of an aerosol, which greatly simplifies the process of its application.

In order to wash the mounting foam from your hands, you must do the following simple steps:

1. Spray the solvent aerosol onto the contaminated area of ​​the skin.
2. Rinse thoroughly with plenty of water.

This tool perfectly copes with liquid, not hardened polyurethane foam. But before the frozen substance, it is powerless.

Important! Before using a special solvent aerosol, you should definitely read its instructions..

Acetone

Pure acetone or nail polish remover containing acetone will help get rid of the uncured mass. The principle of application is extremely simple:

1. Soak a cloth or cotton pad in acetone and gently remove the mounting foam from your hands.
2. Wash your hands thoroughly with soap and running water.

Important! You must act quickly and carefully. Acetone has a specific smell, so it is best to clean it outdoors or in a well-ventilated area..

Kerosene

This liquid is also effective enough to remove sealant from hands. It should be used in a similar way to acetone.

How to clean hands from polyurethane foam at home?

If the above liquids were not found in your home, then you can use improvised means.

Vegetable oil

This option for cleaning mounting foam from your hands is absolutely harmless and safe for the skin.

1. Lightly heat vegetable oil.
2. Soak a cotton swab in the oil and dab the dirt on your skin.

Important! Surprisingly, this tool is able to remove even hardened mounting foam. To do this, you need to arm yourself with patience and hold the moistened cotton wool in oil for 20-30 minutes at the site of contamination.

Salt

Salt is an abrasive substance, so it is able to remove foam and its residues from hands:

1. Rub a small amount of salt on the areas contaminated with sealant.
2. Wash your hands with soap and water.

Important! Hands should be treated with salt very carefully so as not to scratch the skin.

How to remove mounting foam from hands if it has already hardened?

If you did not manage to remove the mounting foam from your hands before it had hardened yet, then the cleaning process will take longer, because practically no solvent mentioned above can remove the hardened mass.

In this case, the foam can only be cleaned mechanically. For this you will need:

• Hard brush, pumice stone or soft sandpaper.
• Fatty cream or vegetable oil.
• Soap.

The procedure should be carried out very carefully so as not to harm the upper layer of the epidermis:

1. Spread the contaminated areas of the skin of the hands with a greasy cream or vegetable oil. This will soften the harsh effect of the brush on the skin.
2. Scrub a stiff brush or pumice stone with plenty of soap.
3. Gently, slowly, rub the hardened foam with a brush.

Important! To make the foam removal process a little easier, you can pre-steam your hands in hot water for 8-10 minutes..

Some people, out of ignorance of the correct solution to the problem, try various means. Subsequently, they either do not get any result or get the desired effect, but cause irreparable harm to the integrity of the epidermis. So, what means to remove the sealant from the skin is not recommended.

Vinegar and other acids

In no case do not experiment with acids, such as vinegar. You will not wait for the desired effect, but getting a serious chemical burn is quite realistic.

Important! This especially applies to the situation when you decide to use not the usual canteen 7-9% vinegar, but 70% essence.

Dimexide

Many recommend this medication as an effective tool for cleaning hands from mounting foam. Indeed, it dissolves building foam well, but it is strictly forbidden to treat the skin with it without an appointment and further control of the doctor.

Important! "Dimexide" is quickly absorbed into the skin and enters the human body. But just like any drug, it has a number of side effects. Therefore, it is better to use it for cleaning soiled furniture, floors and walls, but not leather.

Alkaline products

Do not use detergents with a high concentration of alkali to clean such hand contamination. They are not able to remove traces of sealant, but they will quickly break the normal skin acid balance.

• If you still failed to remove the sealant using one of the described methods, then do not despair. Due to the fact that skin cells are constantly being updated, pollution will clear itself after a while.
• After successful removal of contamination, you should generously smear your hands with hand cream or aloe juice to soothe and moisturize the skin after an unpleasant procedure.

Mounting foam is indispensable in the construction industry, now the same popular euro windows, new doors that are installed using foam. Also, building foam is an excellent heat insulator.

It is easy to work with it, with the help of a special "pistol" the foam penetrates into hard-to-reach cavities and after a few hours, under the influence of moisture, it hardens and turns into a dense mass.

Here are the main properties of building foam, due to which it does not lose its popularity:

· Soundproofing;

· Thermal insulation;

· Sealant;

Installation (fastens separate parts into a single whole).

However, with all its positive qualities, in case of inaccurate work and foam getting on the skin, clothes or doors, it is very difficult to wash it. What to do in this case?

How to wash dried mounting foam?

If you remove the foam while it has not yet had time to harden - there are no problems, it is easily removed. But what to do if she has already frozen ...

If the foam has hardened, then the easiest way is to cut off the excess and scrape it off with any sharp object.

This option is suitable if after that the surface will be covered with a protective layer and it will not be visible.

Now consider the options for building foam to get on other surfaces, including hands.

How to wipe mounting foam from hands?

If the mounting foam gets on your hands, you don’t have to worry much, as you usually immediately notice that the foam has got on the skin and the uncured foam is much easier to remove.

Keep in mind that if building foam gets on your skin, you need to do everything quickly, otherwise you will have to wait until the foam falls off by itself.

· Try to wipe off the foam with a tissue.

· Using benzine, acetone or cleansing, try to dissolve the foam on the skin, you can even use a regular nail polish remover.

· If the above solvents did not help, then take a basin, pour hot water into it and add salt.

Dip your hand with foam in water and steam for about 5 minutes, then try to rub it off using a pumice stone or washcloth.

Soapy water also helps, after steaming the skin, lather it thoroughly and proceed with the treatment with a pumice stone or washcloth.

Take vegetable oil, warm it up to the temperature of your hands (or a little more) and rub it into the skin. Then pour washing powder on the skin and rub the skin with it until the foam is completely removed.

There is a slightly different option - just lubricate the skin with oil and leave for 20 minutes, then rinse with hot water, the mounting foam will easily come off the skin.

How to wash mounting foam from clothes?

To save clothes you will need:

· Purifier;

Sponge and rag;

Knife or scraper;

· Nail polish remover;

Solvents (gasoline, acetone);

First of all, you need to moisten an inconspicuous piece of cloth with a solvent and look at the reaction of the tissue. If everything is normal, proceed to remove the foam.

1. There is a special cleaner that is offered along with the purchase of polyurethane foam, with which you can easily clean clothes.

You just need to apply the cleaner on the stain, hold the number of minutes indicated on the package and collect the remaining foam with a rag or washcloth.

If once was not enough to completely remove the foam from the fabric, repeat the procedure.

2. If the previous procedure was more gentle on clothes, then this one is less gentle.

3. If we do not have a special solvent available, then any others will do. Nail polish remover is the safest for clothes,

4. And use acetone and gasoline with great care, as the dissolved foam will be absorbed into the fabric. The method of application is the same as with a special solvent.

5. You can not smear (wash with a rag) a fresh stain, so you rub it more into the fabric, and do not remove it.

How to clean mounting foam from a door

For this you need:

· Metal brush;

Sharp object (scraper);

· Gloves, eye mask;

· Special solvent for foam cleaning;

· Napkins;

Acetone.

Using a wire brush, remove the foam from the surface, but be careful not to scratch the surface.

Wearing a face mask and gloves, remove the foam with a cleanser.

If there is little foam, use a blade, not a knife.

If the surface is painted or, even worse, varnished, carefully treat with a solvent, as the cleaner can dissolve the varnish and paint in addition to the foam.

To do this, first test the substance on an inconspicuous piece of the door, and then on the foam.

Remove the foam that has not yet hardened with acetone, but keep in mind if it damages the surface of the plastic door as well (but it’s better to do a “test” of acetone in an inconspicuous area)

If you cover the door with paint or other protective coating on top and this layer is not important to you, then remove most of it with a knife, and then with a brush or scraper.

How to remove mounting foam from clothes

What I want to say about this, first of all, when repairing and blowing out cracks with foam, use exactly the clothes that you won’t be sorry to say goodbye to if it gets dirty.

If you have not thought through this part and dressed the “beloved” that you would still like to vilify, then you need to clean it.

Take a knife in your hands and remove the part of the foam that can be removed without harming the fabric itself (that is, cut almost above the surface).

Then using the solvents you have (although it is better to buy a special one for foam and gentle on other surfaces).

Then, using the agent of your choice, do a test on the fabric (on a lining or in an inconspicuous place, drop the solution and look at the reaction of the fabric) if everything is fine, then proceed to treat the stain.

Treat the stain itself and then gently remove the dissolved foam with a rag or napkin (without rubbing into the fabric).

Send the cleaned fabric to the wash (the sooner the better), as the solvent continues to act on the fabric itself and must be removed.

And although, before blowing something with foam, prepare a special fabric that you don’t feel sorry for, protect your hands by putting on gloves and covering the nearest surfaces with a film.

So you not only save yourself from unnecessary nerves and unnecessary problems.

For cleaning hands from contamination with mounting foam, the area of ​​\u200b\u200bcontact of the foam with the skin is of fundamental importance. The larger the stain, the more difficult it is to clean. Even more important is the degree of polymerization (hardening) of the material. If possible, the foam must be removed immediately. After 10-15 minutes, it is much more difficult to do this. Older residues on the skin of the hands are not easy to remove.

Special liquids and aerosols

Foam manufacturers also produce special washes. Most of them are designed for cleaning guns and smooth work surfaces (window sills, door and window frames, doors). Liquids for cleaning hands are not produced, since the cured polyurethane is irreversible. It can be softened only with sufficiently aggressive solvents, contact of which with human skin is undesirable.

But, if skin contamination has already occurred, many builders resort to standard liquids and aerosols, hoping to clean their hands without compromising health.

The released substances are designed only for cleaning from fresh foam:

1. IOFARM R621. Aerosol for cleaning tools, contaminated surfaces, hands. The main active ingredient is acetone. Applicable only for the removal of fresh contaminants.
2. PENOSIL Foam Cleaner. Aerosol for cleaning with fresh, uncured foam. Can be used to remove stains from plastics (leaves no residue).
3. OPPA. Aerosol removal of unhardened fragments. It is also used for cleaning and degreasing plastic and glass surfaces.
4. PENOSIL Premium Cured PU-Foam Remover. Remover for hardened foam. Aerosol. Not effective on adhesive (highly absorbent, porous) surfaces.
5. Cosmofen S5. Plastic polishing agent. Cleans fresh lather. The main purpose is to remove defects and scratches from opaque vinyl (PVC) surfaces.

Very few special solvents are needed to clean hands. Therefore, when choosing a liquid or aerosol, their additional capabilities are important so that the purchased canister is in demand in full.

If at the time of contamination there were no special liquids, common, standard solvents are used:

1. Acetone and acetone-containing liquids (composite thinner 646, nail polish removers). Small amounts are not as toxic because acetone is a product of natural metabolism present in the body.
2. White Spirit. Not very efficient. However, it is better than using soap and water.
3. Solvent 647. Multicomponent liquid based on acetates and toluene. Toxic.

In order to avoid complications from skin contact with aggressive liquids (for chronic allergies), it is possible to use heated vegetable oil. This substance is not so effective. But not without side effects, environmentally friendly.

How to clean your hands from fresh foam

The foam that has not had time to harden (polymerize) is washed off quite easily. The main thing is to follow simple rules:

1. Localize the spot. Contamination is wiped with napkins, toilet paper or soft rags. Movement must be directed to the center of the spot so that it decreases rather than increases.
2. Solvents. Aerosol washes are sprayed from a distance of 10-15 cm onto the soiled areas. If the stain is small, you can spray the substance not on pollution, but on a rag, which can be cleaned from a distance of 1-2 cm.
3. Removal of solvents. After cleaning the hands, they are washed with soap and hot running water.

Fresh foam washes off quite easily. However, it is not always possible to interrupt work for hand care. In this case, you have to face the problem of cleaning from old stains.

What to do if the foam has hardened on your hands

Well-dried foam cannot be removed with ordinary solvents and washes. There are special compositions of substances. But practice shows that they are not effective:

• Pollution practically does not change its properties.
• Solvents are toxic, have a bad effect on the skin of the hands and, being absorbed into the pores, on the liver and cardiovascular system of the body.

For example, PU REMOVER is a paste-cleaner for hardened foam. The substance is indeed capable of softening dried polyurethane foam, but, according to the manufacturer's instructions, it is applicable only on smooth, non-porous surfaces. Excellent proved itself on metals, glass, but not productively on the hands.

Sequence of actions when removing dried foam

The easiest way to clean old contaminants from polyurethane foam is to naturally change the epithelium: the upper layers of the skin periodically change, flake off. Along with them, persistent pollution also “departs”. The process lasts from several days to 7-10 days, but it can be accelerated:

1. Thinning. The foam layer must be made as thin as possible. This is done mechanically: the foam is carefully, so as not to damage the skin, erased with fine sandpaper, pumice stone. Sometimes a razor blade is also used, but this method is not recommended because cuts and wounds are inevitable. It is worth remembering that under the skin of the hands, the veins are located very close.
2. Steaming. Hands can be steamed in hot water (at a temperature of 60-65 degrees). Steaming time depends on the quality of the foam, the degree of its penetration into the pores and the initial condition of the skin.

After 10-15 minutes, hands are wiped and dried. The spot is localized, the thinnest parts of the spots will disappear. Thick ones need to be thinned and steamed again.

If it was not possible to completely wash off the remnants of the foam, a children's moisturizer should be smeared on the contaminated places at night. This method is not as effective as steaming. But it "works" all night and, as a rule, brings certain results.

How bad is polyurethane?

The active substance of the mounting foam is polyurethane foam (PPU). Fresh and in the process of solidification, it releases toxic substances. Therefore, PPU contact with the skin is undesirable and causes irritation, allergic reactions. Frozen, it is no more dangerous than foam rubber.

How to keep your hands safe

It is enough to use rubberized gloves. Ordinary cotton ones are also suitable, but they are not able to fully protect the hands, because they get wet, they are permeable to foam. However, the area of ​​contamination will be reduced, especially if you change them more often.

It should be remembered that it is easier to foresee possible contamination than to remove dried polyurethane stains later. After all, it is so difficult.

Video: how to remove mounting foam from hands

Currently, polyurethane foam is one of the most popular building materials. And this is not surprising. After all, it is mounting foam that is used today both as a sealant, and as glue, and as a sound or heat insulator.

Most of both external and internal construction works are directly related to its application. These are works related to the installation of doors or windows, with the insulation of houses, cladding them with siding, and works involving the laying of pipes.

But, as it turned out, such a multifunctional building material also has one small but very serious drawback: it adheres equally strongly to any material. Therefore, it is not at all easy to remove after hitting unwanted places. Such a nuisance can happen even with a professional in his field. And what can we say about the one who did the repair for the first time?

Ways to wash dried mounting foam

In fairness, it should be noted that a small drop of mounting foam can deliver a lot of unpleasant minutes to a professional. Anyone who has never worked with this building material may not realize how difficult it will be to get rid of even a small speck of mounting foam, because this material clings so tenaciously to any surface.

It cannot be washed off under running water, rather, you can get the opposite effect, because the foam expands and hardens under the influence of water. Little hope can be placed on some of our usual solvents or cleaners. For example, white spirit will not cope with polyurethane foam.

So is it really all that hopeless?

How to wash foam off your hands

How, after all, to wash off the mounting foam that got on the skin of the hands? Of course, it will be much easier to remove a fresh stain using a damp cloth or some kind of cloth.

Some use some kind of skin-friendly solvent. If the foam is still frozen, then, first of all, you should know that this material does not contain any harmful substances, so you should not worry in this direction.

As for the aesthetic side of the issue, experienced builders most often use one proven folk method in this case.

Before you start removing the mounting foam that got on your hands, you should hold your hands in a solution of common salt for some time, approximately 5 minutes. After that, you need to take a regular pumice stone and gently scrape the problem area. So, the desired effect is achieved: hands are clean. Now you should lubricate them with a moisturizing hand cream.

If you still haven’t been able to completely clean your hands, do not worry. It will take quite a bit of time and the foam spots will disappear on their own.

How to clean plastic, linoleum and wood

It often happens that the mounting foam accidentally got not only on the hands, but also on the nearby surfaces made of plastic, linoleum or wood. If the foam stain is still quite fresh, then it can be removed from plastic or glass surfaces using a scraper that would not damage this surface, would not leave scratches on it. After that, using a hard sponge or cloth, the surface is cleaned again.

Some prefer to use a cleaner instead of a cloth. However, it should first be checked on the most inconspicuous area of ​​the same surface. Most often, acetone or products such as solvent 646, Isofoam r621, Cosmofen, Macroflex wash are used.

But the foam that was not noticed immediately, and it has already hardened, will be more problematic to clean. Will have to be patient.

Some builders recommend first cutting off the frozen stain with a blade as close to the surface as possible, and then trying to soak it with a solvent and rub it with a fairly hard sponge. It is best to use SOUDAL PU Remover, which is designed to remove foam that has already hardened.

To remove mounting foam from more delicate surfaces, such as plastic, wood, linoleum, do not use those solvents that are considered aggressive. Some recommend using dimexide in this case. This is a well-known drug, it is sold in any pharmacy. Moreover, it is quite inexpensive, almost a penny.

The existing stain is well moistened and left for several minutes, and then it is removed with a cloth, sponge or even a cotton swab.

If mounting foam has got on plastic windows, then the easiest way to get rid of it is to remove it with an oil solution.

Ordinary sunflower oil is applied for half an hour to the contaminated area, and then cleaned with intensive movements using a regular dishwashing sponge.

Remove hardened foam from clothes

The issue is much more difficult to solve if the mounting foam has got on the fabric or on the clothes. Whether it can be washed off or not will largely depend on the structure of the fabric itself.

It is almost impossible to clean knitted fabrics or knitwear. Foam stains can be removed from denim and leather goods using mineral spirits.

How to clean from glass or metal doors

In some cases, you can get rid of the frozen foam only with the help of a simple mechanical rubbing of the surface with a small piece of plastic. This is how it is recommended to clean a metal door or battery painted with enamel from mounting foam.

Foam stains can be removed from a glass surface in several ways. Some builders scrape it off with a knife or blade, while others prefer the use of a cleaner. Using a plastic scraper, carefully remove the stain from the foam that got on the car.

As you can see, in order to remove stains from mounting foam from various surfaces, you will have to make a lot of effort, and sometimes additional material costs will be required. At the same time, there are cases when it is not possible to achieve the expected effect. Therefore, it would be more correct to prevent the development of this situation and try to protect yourself as much as possible from the ingress of mounting foam on surfaces for which it was absolutely not intended.

Video: how to wipe mounting foam from a car

The video talks about one of the best products for removing dried foam from almost any surface. How to use, how long this procedure takes and what you should pay attention to is detailed in a short but informative video with clear step-by-step instructions.

At the stage of construction and finishing work, you need not only to deal with the choice of materials, but also take care of how to remove compounds that accidentally get on the skin, namely, how to wash the mounting foam from your hands. Such a nuisance can happen to fairly experienced craftsmen, not to mention novice builders.

When deciding how to wipe the mounting foam off your hands, it all depends on whether it has had time to harden. Some tools will help remove the liquid mass, but in this case it is necessary to prepare them in advance before starting work. It can take precious minutes to find the right substance, and as a result, the foam will harden and it is already necessary to use completely different cleaning agents.

Tip: Before performing any manipulations, as soon as the sealant has got on the skin, it is necessary to remove the excess substance.

If the question arose of how to remove mounting foam from hands, it is proposed to implement one of the methods.

Special solvent

It must be purchased before work begins. The release form is an aerosol, which simplifies operation and increases efficiency. A cleaning gun is used to apply foam. It is only necessary to spray the substance over the contaminated area, and then wash off the foam under running water.

Such a solvent is used in strict accordance with the instructions. If the question is being solved, how to clean the mounting foam from the hands after it has got on the skin, then the aerosol will quickly cope with this problem. But in the case when the building material has already hardened, it is useless to use such a solvent.

Vegetable oil

A proven folk remedy is vegetable oil. How to wash mounting foam from hands in this way? It is necessary to use heated oil, which will somewhat improve the effectiveness of the cleaning process.

It is recommended to apply it directly to the stained area or place a cloth/rag soaked in oil on top. In this position, it is recommended to withstand up to 30 minutes. After that, simply wash your hands, removing the remaining foam. This tool is not the most effective, however, it is completely safe for the skin.

You can use not only acetone, but also its simpler counterpart - nail polish remover, or kerosene. When deciding how to wash the mounting foam from your hands, it is recommended to choose the first of these substances. Nail polish remover is also suitable, but less effective.

Acetone is used as follows: a substance is applied to a rag, then the foam must be wiped off the skin. The faster this is done, the greater the chance of a good result, because acetone is effective until the foam has completely solidified. In the absence of this substance at hand, it is allowed to use kerosene.

white spirit

This is an excellent effective tool for removing fresh mounting foam at home.

Salt

Table salt with large fractions. This abrasive tool will help get rid of mounting foam. It is used for minor contamination. Salt thoroughly rub your hands, after which you need to rinse them under running water.

There is information that the drug Dimexide is very effective in removing mounting foam. This is a fact confirmed in practice, however, it is better to use this solution in other areas (), since the medicine is quickly absorbed into the skin of the hands, which can cause side effects.

The nuances of removing foam in a frozen form

If for some reason it was not possible to clean the skin of the hands in a timely manner, you will have to think about how to wipe off the dried mounting foam. Solvents do not affect the sealant in the solid state. For this purpose, any abrasive means of mechanical action are suitable: a hard brush, pumice stone. A coarser grit sandpaper will also work.

Tip: Before starting mechanical treatment, you should steam the skin, for which the hands are dipped in hot water for several minutes (no more than 10 minutes).

The sequence of actions at the stage of cleaning the dried foam:

• hands are lubricated with a high-fat cream, oil, which will reduce the intensity of the impact of the abrasive surface on sensitive skin;
• brush / pumice is lathered;
• it is necessary to clean the skin of foam carefully and at the same time, providing sufficient pressure so that the sealant layer begins to lag behind.

If it was possible to remove the foam, you need to wash your hands, and then spread the cream again.

In the case when the main products have been tried, and the skin has not become perfectly clean (small areas, traces of foam remain), you should be patient and wait 2-3 days. During this time, skin cells regenerate, and there will be no trace of pollution.

If, before starting work with the user, he was poorly prepared and does not know how to wash the mounting foam from the skin of his hands, mistakes are often made: improvised means (Domestos, acetic acid) are used. In such a situation, you can easily get a burn, but there will still be no result. Therefore, it is necessary to take a sensible approach to the issue of cleaning, avoiding ineffective, but at the same time quite dangerous means under certain conditions.

Tip: Considering that the hands are in any case exposed to aggressive substances or abrasives, it is recommended to apply a cream with regenerating and antiseptic properties to the skin at the end of the foam removal process.

So that in the future you do not have to look for a solution to the problem, how you can wipe the mounting foam from your hands, you should prepare more carefully:

• while working with the sealant, goggles and gloves are worn;
• work clothes are used, as they are more likely to be soiled;
• the hair must be closed, because in this case it will not work to remove the foam without harming the hair;
• all interior items and furniture are covered with foil, cardboard.

It is advisable to invite an assistant for work, since the sealant hardens very quickly and you need to insure yourself: somewhere you will have to fix the protective coating of the furniture, hold the gun in another place, or remove a drop of foam quickly emerging under pressure.

Thus, the best hand cleaner is the one that is most suitable for working with a substance of a certain structure. Liquid sealant is easier to remove with a special solvent, acetone. Even kerosene and warm sunflower oil will do. The hardened foam is cleaned off mainly with abrasive products (emery, pumice stone, hard brush). Foam cleaning should be done as quickly as possible, as removing hard sealant is a more difficult task.

tweet