Wired router connection. How to connect to the router: step by step instructions. How to connect a Wifi router if there is a wired Internet
Correct settings distribution points of your local network guarantee not only ease of use, but also protect against possible hacking by hackers. Let's proceed to the analysis of the question of how to connect to the router.
First of all, we connect the power cable and the power cord to the appropriate connectors, which you can see in the instruction manual. Please note that one of the connectors is colored blue - this is an external WAN connection, to which a wire from your provider should be connected. That network cable, which is connected to one of the white connectors, and should be included in our computer.
Since only a network connection can be used to control such equipment, the answer to the question of how to connect to the router via the Internet is obvious - using a web browser.
Login to the web interface
Your PC should already be turned on: launch any web browser and start connecting to the router, for which we enter the numbers 192.168.0.1 in the top (search) line (or others, this is indicated in the device manual or on the factory sticker that is on it) . Then we see a similar picture.
By specifying the default login and password written on the bottom side (if this is not a new device or the data has been replaced by someone, then you need to reset all settings by holding the button near the power connector for 6 seconds) you enter the web interface of this device.
Change the factory administrator password
After that, immediately go to the "System Tools" - "Password" tab and change the login with the password to your own and click "Save". Be sure to write them down on paper.
Connecting the router to the Internet
After that, go to the "Quick Setup" tab and select your provider, or check the box as indicated below, and click "Next".
On the next page of the wizard, you can select the mode for obtaining settings automatically or enter them manually. What exactly to choose, you need to find out from your provider.
After that, let's find out how to connect to the router through -, for which we go to the "Wireless Mode" tab.
First of all, you will need to replace -, which the router will distribute, and turn off the broadcast of this name publicly. To do this, enter the network name and uncheck the box next to "Enable SSID Broadcast". Do not forget to click "Save" and write down the specified name in your notebook.
Now the name of your network will not be visible to third parties: instead, they will see a message that there are some “Other networks”, and without knowing your SSID, they simply will not be able to connect to your router, which will increase its security. To connect to - the router via -, you also need to specify the type of encryption (tab "Wireless Security").
Choose encryption and set a password
For maximum security and internet speed the best choice is WPA2. Enter the password for your wireless network and write it down. Click "Save".
It remains quite a bit to figure out how to connect to the router. Some models will need to be rebooted for the entered network name and password to take effect. IN this case you need to select "System Tools" and then "Restart".
We connect the laptop (gadget) to the access point via Wi-Fi
Let's start connecting to the router. Around the clock, left-click on "Other networks" (as you remember, our device does not broadcast its name and therefore is invisible in the list). Click "Connect" and enter the network name.
Home-small office network devices are represented by a very wide choice. A separate class is routers, that is, combined systems, designed to connect to the Internet provided by your provider, and further broadcast (distribute) traffic to one or many network devices. The local network can be wired (100 Mbit or 1 Gigabit), and also wireless, operating on the Wi-Fi protocol. How to set up a router at home, we will consider in detail in this review.
The user has already decided on the choice of model, or, moreover, the acquisition has already been made. It can be a 100-megabit, or "cutting edge" gigabit router model, with one or two Wi-Fi bands. However, without proper settings, revealing the maximum functionality is unlikely to succeed.
Installation and connection
First of all, it is worth deciding whether “wired” connections will be used, or the entire local network with Internet access will be organized completely “via Wi-Fi”.
Based on this (that is, from the number of "wired" lines), the installation site of the router is selected. At the same time, the length of the cord "from the provider" (in the figure - "green") - should be as short as possible. But, do not rush to change anything: when you turn it on for the first time, the cable should “reach out” to the computer (from which the router will be configured).
Remember: the router, like other devices (for example, a modem), is powered by outdoor unit. A similar adapter is plugged into a 220 volt outlet. When choosing a location for installation, you need to consider safety rules.
Fastening
Almost every router allows installation in horizontal position(on the table, on the shelf). On the case, especially for this, rubber inserts (“legs”) are provided. At the same time, the vertical version of the case installation does not allow every device. If you install a horizontal case vertically, overheating of the internal hardware (and various other troubles) is possible. How to install a router at home - the user decides first, and only then, makes a choice of a specific model. A definite plus will be the ability to attach to vertical surface(that is, against the wall). Be careful when choosing.
Connection
Any router, as a rule, contains 4 hardware ports for the local network. It is necessary to determine which devices (computer, laptop, TV set-top box) will be connected “by cable”, and all the rest will be able to access the network exclusively via Wi-Fi.
Port Assignment
Consider how to connect a router at home on your own (while not violating the warranty rules).
- Connect LAN cables (ports 1-4) if any will be used.
- Connect the provider's cable to the "Internet" port of the router (another name is the "WAN" port).
- Then, the power supply of the router is connected, plug it into a power outlet.
That is, turning on the power supply is performed last.
Setting
Any retail kit, in addition to the router itself, includes two “devices”: a power supply, as well as a power cord (patch cord). During the initial (first) setup, we recommend using the supplied cord. That's right, you make sure the router is working.
Before you connect a wifi router at home, the first time you connect it "next to the computer."
If the router is new, the next step is skipped. Turn on the power of the router (it is not necessary to connect power cords). After 2-3 minutes, press "reset" (holding for 5 seconds or more - read the instructions), all settings will be reset to "factory".
Also, you need to check that the PC network card is set to “auto” mode (IP, DNS). You need to look: "Connection properties" - "TCPIP protocol (v4)" - "Properties". It should be like in the picture (install, click "OK"):
Setting up a network card
Now, with the power off of the router, you connect its port (from 1 to 4) to the PC network card. What is done with a patch cord.
Then, turn on the power. It is advisable to restart the computer. How to set up a router at home is described in detail in the instructions.
After switching on, you need to wait 2-3 minutes. Then, a local connection will be established (which means the device is working):
Open a browser. In the address bar, you type the router's IP address (web interface address):
What it is (for your router) - see the instructions. In the same place, give "login" and "password":
Without knowing the “login with password”, you won’t get to the setup page, and you won’t be able to configure the router further.
Note: if you want to set up a connection with your provider, you need to connect the cable to the "Internet" port (to the "WAN" port). What happens before power is applied.
Port Assignment
Web interface
All settings are performed by the user in the web interface. This is such a set of tabs (pages) displayed by the browser. Each page configures one thing: Wi-Fi network (name, range, etc.), Internet connection (properties of the "WAN" port) ...
Note: After making all changes on one tab, save them before moving to another. Saving many settings "immediately" - leads to damage to the device!
However, the advice given above does not apply to modern models. It must be remembered that some types of settings will “take effect” after a reboot. You can reboot the router by pressing reset "in one click".
In conclusion, consider how to set up a router WiFi at home, where the wireless network is "seen" only by you. Necessarily:
- 1. Come up with a name for the Wi-Fi network (by setting it in the SSID field):
WiFi settings
The name then - you can “hide” (tick “hide access point”).
- 2. Setting the "country" - will change the list of available channels (there are 14 in total, for the 2.4 GHz band).
- 3. Wi-Fi network, can work in “b / g” or “n” mode (it is the fastest), if you don’t know, “mixed” is recommended.
In this model, you can set the maximum number of Wi-Fi users (zero means "auto"). You may have other settings (read the instructions for details).
"Hiding" the name is a method to protect your network. Traffic encryption (WPA2, WPA), password entry (PSK) - referred to as "advanced" methods. To install them, there is a separate tab (“ WiFi settings security").
We hope the information will be useful.
Today's review quick setup tp-link router. As an example, I will use the TL-WR841 model, but I want to say that other routers of this company will be configured in the same way.
Actually, I am writing the article in order to answer the question that a young girl asked me yesterday through the form feedback: "Ask a Question". You can also ask me any question related to computer and software in as soon as possible I will give detailed answers.
How to set up a TP LINK router
The essence of the girl's question was that she was trying to set up a router, not only to work with wifi network yu, but also in parallel connect access to the Internet to a personal computer ( system unit). Based on a few tips, she managed to connect the cable and make Internet access on the PC, but the Wi-Fi network remained inactive.
I wanted to help the girl in text format, but for some reason her parents disposed of the box from the router, in which the instructions and the installation disk remained. Based on this problem, I will try to describe in detail the solution to the situation with several options. And at the end you can watch a video review, where I will show all the necessary actions and settings on my laptop.
So, let's start solving all the issues in order, but until I begin to describe in detail the necessary actions, I advise you to read the article what is wi-fi. This will allow you to be more competent in solving issues of this subject.
Setting up a router with a complete set
In order to start installing the router, check the necessary components, prepare them so that you do not run later. To set up you will need: a router, a power cable, a power cord, an installation disk
(if you don't have an installation disc, you'll first need to download the disc image. To do this, skip to the next section and then come back here).
The order of actions may vary slightly, but I do it in this order:
Watch the pictures carefully and repeat the same for yourself.
We launched the disk, as a rule, it has several settings for different routers. We choose our model.
In the next window, select the language and click start installation.
After the appearance of other windows, always click next. Checking and configuring parameters will appear, checkboxes will light up about successful installation.
Carefully fill in all pop-up windows or put a tick on the line "I did not find the necessary settings."
If such a window pops up, then you need to select the type of connection. You can find out what type of connection you have by reading the contract that you have concluded with the provider. The most popular is PPPoE. But to be sure, be sure to check, or you just won't complete the installation.
Now let's move on to the most unpleasant, look for your username and password for access in the agreement with the provider and enter it in the appropriate windows. Click next again (if you don’t see such a window, then just move on).
In the next window, write the name of your network in English letters.
We come up with a password to access our network.
Now we confirm our data.
Let's show a little patience and just wait, at this stage the final setup is underway.
So in about 5 minutes, we fully configured the router and the network is ready for use. After successful setup, you can close the program. Remove and remove the installation disk and disconnect the network cable that connected the router and the computer.
We check the wi-fi network using any supporting device (smartphone or laptop), make sure that the network is working, and you can go online. Now you can put the router in a place convenient for you.
What to do if you lost the installation disk from the router?
To emerge victorious from this situation, you will need to download an image or utility for this installation disk from the manufacturer's website.
To do this, go to the site, look for the model of your router. Go to the search tab and type in the model of your router, on some sites this may be a support section. By the way, you can also download the image of the installation disk from other sources, but no one knows whether you will catch a couple of viruses.
As an example, I go to the Tp-Link website, go to the search field, enter the router I'm interested in.
Several search results will appear below, of which we select the one we need and scroll until we see something like this line, in the bark there is a “downloads” section.
In the download section, we need to find software and download the version of the utility we need.
To find out which version you need, turn the router over and reverse side you will see a sticker on which there is a version of your equipment.
Once we have decided on the version, click on desired section and scroll to the very bottom of the page. Until the moment where it will be possible to download the utility to your computer.
Now we return to the first stage of setup. At the moment when you need a disk, just run the utility or disk image file and safely continue the quick setup.
Connecting the router to the PC system unit
If you have successfully completed setting up the Wi-Fi network, then you can proceed to the next step. Namely, connecting the router to a personal computer, where there is no possibility of working through a wi-fi network.
To do this, you just need to take the network cable that was included and insert one side into the slot of the router, and the other into the network slot of the PC or other equipment. Wait about a minute and check if an Internet connection has appeared on your computer.
By the way, most likely the network cable in the kit will be very short, which causes some inconvenience. I recommend purchasing a cable of the length you need, they are not expensive.
Video review on setting up a router using quick installation
If you have additional questions on the topic, then do not hesitate to write them in the comments of the article. Only with your help will it be possible to add and update information on the site in a timely manner.
The site invites you to read the article on connecting the network and the Internet using a WIFI router, we will try to connect the WiFi router on our own without calling a specialist at home. There are two types of routers - without Wi-Fi and with it, let's try to configure our computer and router to use a wireless network.
And so we have a router available, no matter what manufacturer your router has, the principle of connecting WiFi routers in most cases is the same for different models. Now in almost every house and apartment, there is a device that supports WIFi connection, laptops, phones, TVs, smartphones, tablets, game consoles and printers.
How can you connect the Internet yourself through a router, and organize sample diagram internet work at home. All we need is a communication channel that comes to your house using a regular network cable or a coaxial cable (in the form of an antenna). In this review, we will consider directly connecting a computer and laptop to an access point. Now let's take a closer look at the WiFi router itself and what it is. Externally, they may differ, but the rear panel has the same outputs and connectors.
And so we see an interface for connecting the incoming Internet, as well as a couple of interfaces for organizing an internal network using cables. In the role of the incoming Internet, it can be either a regular network cable, or a telephone cable if you have an xDSL connection. In addition, there are also USB modems, but they are rare.
To connect a computer to a WIFI router, we need a wired network cable (patch cord). Even if your desktop computer has built-in Wi-Fi, it is recommended to connect using a cable. This is the fastest connection method and provides a reliable connection between your computer and the router. If your router is still located far from the computer, then you can connect it via WiFi, but I recommend using a cable. Since you will not carry the system unit with you like a phone or a laptop, it will be more expedient to use a cable. A patch cord usually comes with any WiFi router and looks like this:
In addition to a computer, a TV and other devices that require a more stable connection to your router are connected using a cable. Of course, you can also use a WiFi connection, it's just that initially a wired connection is designed for a large bandwidth. The cable is plugged into one of the free ports on the LAN1 or LAN2 router, etc., and the other end of the cable is inserted into the system unit as in the figure:
Next, we wait until the access point gives our computer a network address, and go to the router to configure it directly. Usually the network address for the router is 192.168.0.1 or 192.168.1.1. This address is listed in the instructions for the router. If you entered the address correctly, then you will see a window with a name and password for authorization. The password and login are also indicated in the instructions. If they suddenly do not fit, you can use the Reset button and restart the WiFi router.
Let's say you got into the modem interface, it remains to check and configure the type of your Internet connection.
1) If you have static settings network connection then you need to transfer these settings to the router settings:
First of all, you will need to replace -, which the router will distribute, and turn off the broadcast of this name publicly. To do this, enter the network name and uncheck the box next to "Enable SSID Broadcast". Do not forget to click "Save" and write down the specified name in your notebook.
Now the name of your network will not be visible to third parties: instead, they will see a message that there are some “Other networks”, and without knowing your SSID, they simply will not be able to connect to your router, which will increase its security. To connect to - the router via -, you also need to specify the type of encryption (tab "Wireless Security").
Choose encryption and set a password
For maximum internet security and speed, WPA2 is the best choice. Enter the password for your wireless network and write it down. Click "Save".
It remains quite a bit to figure out how to connect to the router. Some models will need to be rebooted for the entered network name and password to take effect. In this case, you need to select "System Tools" and then "Restart".
As soon as a user, besides a computer, starts using another gadget to use the World Wide Web, he immediately has the problem of providing him with Internet access and at the same time not incurring additional communication costs. But, more often than not, there are even more than a few home devices with the function of surfing the global network. For optimal solution problems, as a rule, a device distributing the Internet, i.e., routing it to all computers and gadgets available at home.
However, just by purchasing this device in the store, the problem cannot be solved, but you still need to know how to correctly connect the router. Below in simple terms with drawings detailed description all actions, how to connect a router to a computer using Wi-Fi or a patch cord cable for a router, as well as how to connect a wireless router correctly so that everything works well later, and as the people say, it became Wi-Fi, making the Internet available there where needed.
In order to eliminate the often occurring difficulties, a guide is presented at the end on how to correctly connect a router to a router and configure them. The instructions set out in equally applicable to any models of wireless and wired access points.
The essence of the device
Before proceeding directly to the issue of connecting the device, you need to know the basic principle of its operation. Experienced users can simply skip this section of the guide and go straight to the next one.
A router is a device that independently performs a connection to the global network using the parameters entered into its interface, in fact, this small-sized device acts as a computer, but with a routing function, so the router can distribute the Internet to many devices via Wi-Fi or cables.
Physically, only the router itself is connected to the worldwide network, the router is assigned a specific IP address. Therefore, you will not need to pay extra for a lot of computers or smartphones connected to it, of course, if additional services have not been purchased.
Connection procedure
The router itself is very simple, and it is not necessary to have a significant amount of knowledge for this. On the case of all routers there is a special “Internet” socket where you need to connect the wire from the communication service provider (this connector is called “WAN”).
Next to it are the "LAN" connectors, it is to one of them that you need to connect a patch cord to the network card of a PC or laptop. And also through these ports, wired communication is carried out with various set-top boxes, Smart TV, additional computers etc., which also play an important role for the home.
Now we will step by step analyze the question posed, how to connect the router. It will take only a few consecutive steps:
- Insert the wire from the provider into the "WAN" connector;
- Use the supplied wire to establish a connection between any of the “LAN” connectors of the router with the same socket of the PC network card;
- Supply power to the device through the supplied adapter by connecting it to a 220 V network. Then, if available, by pressing the “On” key. activate the device on the router case (in this case, special indicators on its case will start to glow);
- Ready! The router is connected. It remains only to enter the necessary settings.
Connect the router for further configuration, it is also available without a cable connection to the PC, but by connecting to it via Wi-Fi. But this is a less reliable method. Especially when this is done by a beginner, after entering the parameters, having already reconnected, there are often malfunctions. Of course, they can be quickly eliminated, but in case of insufficient experience of the owner of the device, correcting them will require a significant investment of nerves and time. Therefore, it is highly recommended to use a wired connection to enter settings.
Connecting an ADSL Router
The principle of operation is completely similar to the algorithm described in the previous section of this manual, but this router does not have a WAN port and is replaced by a connector with the name “Line”. After connecting, you can immediately start entering the ADSL Wi-Fi router settings.
How to connect a router to a router?
If you need to cover large area wireless signal coverage, for example, in the case of a large apartment or house, this is effectively done by connecting the router to the router. This is guaranteed to increase the coverage radius of Wi-Fi.
Schematically, this can be shown as follows:
In total, there are 2 main methods for implementing the task:
- With cable;
- Through WiFi.
1 method: Wired
You will need a cable called a twisted pair cable that is long enough to connect the 2 routers together.
In order to connect, you need to do the following:
- Install one end of the wire into the "LAN" socket of the router connected to the global network;
- Insert the other cable plug into the “WAN” connector of the 2nd router;
- Next, enter the settings in the 1st router to configure for the Internet provider, and in the 2nd for dynamic ip.
Method 2: by Wi-Fi
If there is no possibility of pulling a wire between devices (which is extremely common), then you will have to use the second method, which is characterized by the complexity of the settings, so we will pay more attention to it in this manual.
The user has access to a router with access to the global web (let's designate this router as "1st") and another device for use as a repeater - "2nd".
At the first stage, you need to connect the “1st” to the PC and configure the Internet settings on it. Then connect the "2nd" to the PC and configure the connection to the access point.
The algorithm of actions includes the following sequential steps (given for the Windows 7 operating system, but the algorithm is completely similar, with minor changes, for other versions of Windows):
Recently, more and more subscribers of Internet providers are puzzled by the question; how to connect and configure a router through an existing router; with WiFi or without?! For what? There may be several events. 1st and most common cause; zones WiFi coverage the existing device is not enough for the entire apartment or house and it somehow needs to be added. The second reason; savings. Let's say one person has connected the Internet and the tariff is 100 Mbps. And he has a friend next door. And so they decide to use the same Internet channel together, both want to have a wireless network. Another reason; when connecting to the provider, you have already been given an access device: a modem or an optical terminal, but its functionality is not enough. In this, they will just be helped by connecting another 1 to the existing wireless router. In this article, I will tell you how to do it more correctly and give two ways to set up a router-router network: via WiFi and via cable.
Method 1. WiFi connection.
This way, in my opinion, is more correct; one device simply extends the WiFi coverage of the other. In general, at first there was simply a repeater (repeater) mode, which was either supported or not. Later appeared new development; WDS, which manufacturers of wireless devices began to actively implement in their creations.
WDS (Wireless Distribution System) is a special development that allows you to expand the coverage area of a Wi-Fi wireless network by combining several access points (or several WiFi routers) into one network without the need for a wired connection between them. The main requirement for organizing such a network; all base stations in a WDS network must be configured to implement the same frequency, encryption method, and encryption key.
As a result, in order to connect a router through a router via WiFi, the first one should simply distribute a wireless network and no additional options need to be done on it. And the second one should be able to work in repeater mode, or support WDS technology, which is practically the same thing. To know; whether your device can do this; You can either on the manufacturer's website, or by climbing through the settings. As an example, I will consider two wireless routers that can be connected to others via WiFi. 1st; Asus RT-N12 D1, able to work as a repeater. And the 2nd example; TP-Link supporting WDS technology (TL-W741ND, TL-W841ND, TL-W941ND, TL-W1043ND).
Connecting an Asus router to a network via WiFi
In order to switch Asus to repeater mode, you need to go to the web interface, find the Administration section; and on the Operating mode tab; put a checkbox Repeater mode;:
This is a list of available wireless networks. You need to find an existing network, enter the network key (password) and click the Connect button ;. After that, Asus should connect to the network, get an address and expand the coverage area.
Connecting a TP-Link router via WiFi
Most modern TP-Link models have WDS support. In order to configure the connection of the 1st router through another, you must first go to the Wireless Settings section of the web interface; and check the box Enable WDS (Enable WDS);:
You will have access to more options below. We press the Search button and we see a list of Wi-Fi wireless networks available for connection:
We find our own among them and press the Connect button ;. After that, you will be taken back to the Wi-Fi function, where you will need to enter the password for the network and click the Save button. After that, TP-Link will connect to the 2nd access point as a repeater and expand its wireless network coverage.
Method 2. Connecting via LAN cable.
The method of creating a wired network router-router is suitable for you if the distance between them is more than 30 meters. There are 2 options for connecting routers with a network patch cord:
; Option 1. We connect the LAN port of the 1st device and the WAN port of another. The 2nd device will work as an ordinary client of the first one and will have its own separate WiFi network. With all this, it is fundamentally correct to connect the devices to each other. It is necessary to connect the ports as in the photo:
In other words, you must connect one of the LAN ports of the first device, into which the provider's cable comes, with the Internet (or WAN) port of the second. I would not recommend connecting them via LAN ports (although I also considered this option below), since this is not entirely correct. After that, you still need to configure everything correctly. On the first router, in principle, nothing needs to be done. The only thing; check that the DHCP server is enabled in the LAN section. On the second; You need to go to the WAN section and select Connection type; ; Dynamic IP; (WAN Connection Type ; Dynamic IP):
After that, you will need to configure the WiFi network in the usual way, save the functions and reboot the device. After that, the 2nd device should receive an IP address from the network of the first one and work as one of its clients, distributing what it has already acquired to its clients.
By the way, on some WiFi routers, the connection type; Dynamic IP; used by default, on industrial settings. These include devices from D-Link:
Here, to connect it to another, you just need to connect the cable and set up the Wi-Fi network.
; Option 2. We connect the LAN port of the 1st device and the LAN port of another. In this case, both devices will logically be in the same sector of the network. With all this, the wireless networks of both routers will have related addressing, but different names networks; SSID. Setup: First, you need to disable the DHCP server on the second device:
Later, if they have the same IP address on the local network, then it is necessary to change it on the second device to another one so that there is no conflict:
The second router must either be assigned an IP address in the same subnet, but somewhere at the end of the range; for example, 253rd or 254th address. Or even change the subnet to 192.168.2.x for example. Don't forget to save features.
I have listed more optimal, in my opinion, ways of the connection function. If you have any other ways to organize a network via cable or WiFi between routers; write in the comments.
