Vase with fruit with their own hands. Master class with photo. DIY Vase - Personalized Home Decor Fruit Paper Vase
Try to cut out such a Vase for fruits. It will certainly appeal to your loved ones by placing it in a conspicuous place, for example, on a shelf. To make this craft, you will need the following:
Sawing tools.
Fruit bowl
Preparing your desktop
First of all, you need to prepare your table on which you will work. It should not have unnecessary things and every tool should be at hand. Not everyone has their own desktop and probably already thought about creating it. Making a table is not difficult - it is difficult to choose a place for it in the house. Perfect option- this is a warmed balcony on which you can do crafts at any time. I already wrote about table preparation in a separate article and tried to describe the whole process of its creation in as much detail as possible. If you don't know how to prepare your workplace then read the following article. After you have completed the process of creating a table, try to start choosing your future craft.
Choosing a quality material for a vase
The main material is plywood. Its choice is always difficult. The estimated thickness of the plywood for the vase is 6 mm. Each of us must have faced such a problem as delamination of plywood from the end part and asked such a question, why such delamination? Well, it's mostly due to low-quality plywood. If you took the jigsaw in your hands not for the first time, then you can pick up plywood from the remnants of the previous craft. If you are new to sawing and you do not have plywood, then buy it at a hardware store. Choosing material for sawing is always difficult. You should always choose plywood carefully, more often look at the defects of the tree (knots, cracks) and draw conclusions. The complexity of choosing plywood lies in the fact that no matter how you miscalculate its flaws and shelf life. For example, you bought plywood, cleaned it, translated the drawing, and suddenly it began to delaminate. Of course, this happened to almost everyone and it is oh so unpleasant. So it's better to pay attention when choosing and choose good plywood. I wrote a special Article, which describes step by step all the principles of choosing plywood.
Stripping plywood
We clean our plywood with sandpaper. As you already know, “Medium-grained” and “Fine-grained” skins are used to clean plywood in sawing. In construction stores, you probably saw skins (sandpaper in a different way), and they are what we need. In the work you will need "Coarse-grained", "Medium-grained" and "Fine-grained" skin. Each of them has its own property, but a completely different coating, in which it is classified. “Coarse-grained” skin is used for processing rough plywood, i.e. which has many defects, chips, as well as cracks.
"Medium-grained" skin is used for processing plywood after "Large" skins and has a slight coating. "Fine-grained" or otherwise "Nulevka". Such sandpaper serves as the final process of stripping plywood. It gives plywood smoothness, and therefore plywood will be pleasant to the touch. Sand the prepared plywood in stages, starting with medium-grained and ending with fine emery. Grind along the layers, not across. A well sanded surface should be even, perfectly smooth, glossy in the light and silky to the touch. How best to prepare plywood for sawing and which sandpaper is better to choose Read here. After stripping, check the plywood for burrs and small bumps. If there are no visible defects, then you can proceed to the process of translating the drawing.
Drawing translation
For me, the translation of a drawing has always been the main process in my work. I will tell you a couple of rules, as well as tips for high-quality translation of the drawing. Many transfer the drawing to plywood not only with a pencil and copy, but also with the help of the Black Tape, glue the drawing with plywood, then wash off the drawing with water and the drawing markings remain on the plywood. In general, there are many ways, but I will talk about the most common method. To transfer the drawing to the prepared plywood, you must use a copy, a ruler, a sharp pencil and a non-writing pen. Fix the drawing in plywood with buttons or just hold it with your left hand. Check if the drawing fits the dimensions. Arrange the drawing of the clock so that the plywood sheet is used as economically as possible. Translate the drawing with a non-writing pen and ruler. You should not rush, because your future craft depends on the drawing.
Drilling holes in pieces
As you have already noticed, there are parts of the grooves in the details that need to be cut from the inside. To cut out such parts, it is necessary to drill holes in them using hand drill or, as in the old fashioned way, make holes with an awl. By the way, the diameter of the hole must be at least 1 mm, otherwise you can damage the elements of the drawing, which, alas, are sometimes difficult to restore. In order not to damage your desktop when drilling holes, place a plank under the workpiece so as not to damage the desktop. Drilling holes alone is always difficult, so ask a friend to help you with your business.
Sawing details
There are many rules for sawing, but you need to be based on the most common ones. First of all, you need to cut out the internal parts, only then along the outer pattern. There is no need to rush when cutting. The main thing is to always keep the jigsaw straight at an angle of 90 degrees when cutting. Cut out the parts along the lines you marked exactly. The movements of the jigsaw should always be smooth up and down. Also, don't forget to watch your posture. Try to avoid bevels and bumps. If you get off the line while sawing, don't worry. Such bevels, irregularities can be removed with flat files or “Coarse-grained” sandpaper.
Rest
When sawing, we often get tired. Often the fingers get tired as well as the eyes, which are always in suspense. At work, of course, everyone gets tired. In order to reduce the load, you need to do a couple of exercises. Exercises you can see here. Do the exercises several times during the work.
Stripping Details
It is always necessary to clean the details of future crafts carefully. At the very beginning of work, you already cleaned the plywood sandpaper. Now you have to do a small part of plywood stripping. With a “medium-grained” sandpaper, clean the edges of the parts and the back of the plywood. "Fine-grained" skin is considered the final stage of cleaning parts. Fine sandpaper is better to clean front part details. When processing plywood, take your time. You can also use a rounded file, with which it is convenient to clean inner part holes. Try to get the details without burrs and bumps.
Assembly of parts
Assembling the details of our crafts here is not so difficult. In order to carry out correct assembly Details You need to read the following Article, which details all the details of the assembly. After the parts are assembled into one common craft without any problems, then proceed to gluing them. 
We glue the parts
It is necessary to glue the parts of the shelf with PVA or titan glue. You don't need to pour a lot of glue. It is better to tie the assembled craft on glue with a strong thread, tighten it and put it to dry. The craft sticks together for about 10-15 minutes.
burning crafts
To decorate our craft with a pattern (for example, along the edges of the craft), you will need an electric burner. Beautifully burn out the pattern can be very difficult. To burn out patterns, you must first draw a pattern with a pencil. You can read how to work with an electric burner and add patterns to a shelf here.
DIY varnishing
If desired, you can transform our craft by coating it with varnish “On Wood”, preferably colorless. Read how best to Varnish crafts. Try to choose a quality varnish. Lacquering is done with a special brush "For glue". Take your time. Try not to leave visible streaks and scratches on the craft.
In one of the stores, I saw an original vase, which I really liked with my unusual design. It was quite expensive, as it was handmade. Arriving home, I decided to make the same flower vase with my own hands! I photographed the whole process of work and presented it to you, dear readers!
For this project you will need the following tools and materials:
- deep glass bowl For this project, you can choose any container from different material with a smooth surface.
- rope or twine. For the project, I needed about six meters of twine
— glue gun
- scissors.
Process of creation original vase:
- Attach the end of the rope, smeared with glue, to the bottom of the container. And gently glue it in a circle, continuously lubricating with hot glue. The process will be continuous until the end of the rope covers the top edge of the container.
- When you reach the top edge, then take the scissors and cut off the excess part of the rope, and grease the remaining end with glue and glue it to the inside of the bowl.
- Then decorate the bottom of the container. To do this, wrap the rope around, forming a coil. Glue each turn of the rope with glue. Glue the created coil to the bottom in the middle of the container. Do not cut off an unnecessary piece of rope!
- Start gluing the end of the rope around the inner surface of the bowl, smearing it with glue.
DIY autumn crafts from salt dough
Needlework master class: “Vase with fruits”
Knyazeva Irina Anatolyevna, educator of Branch No. 1 of MBDOU No. 137 of PenzaThe master class is designed for preschoolers 6-7 years old, younger students of their parents and teachers.
Purpose: Material for role-playing games, for a gift, for interior design.
Target: making a gift with your own hands, making material for the game
Tasks: Arouse interest in the knowledge of nature and the reflection of the received ideas in artistic images. Develop the child's imagination, fantasy, fine motor skills, accuracy.
Hey pear! What a marvel!
And blush, and beautiful.
The pear asks very much:
"Eat me, Vanyusha."
native apple,
Ours, bulk.
Will grow in our garden
I'll follow him in the fall.
lilac plum,
Ours is a garden
Delicious, tender
Very helpful.
And from a ripe plum
We can make jam!
grapes, grapes,
Lots of berries in a row
Grew up on a branch -
Eat, kids!
Amosova N.V.
Materials: small sawdust; PVA glue; vegetable oil; starch; paints; stack round mold (you can use a scrambled egg mold or an egg container); scissors; a piece of cling film; vase; twigs 6 pieces; board; rolling pin; carnation; wire; glue "Titan"; thermal tape; varnish; brush.
Stages of work:
Sift small sawdust through a sieve.
Sawdust dough recipe:
2 glasses of sawdust;
0.5 glass of starch;
3 tablespoons of PVA glue;
0.5 cups of water;
1 teaspoon vegetable oil.
Dissolve PVA glue in water. Mix starch and sawdust well, and slowly add water mixed with PVA glue. Then add oil while constantly stirring. The resulting dough is similar to shortbread.
1. We line the form polyethylene film.
We make apples. Roll the dough into a ball with a diameter of 5 cm.
On one side, make a recess with a stick with a round end.
Insert a branch into the recess.
On the other, insert a clove.
In order not to wrinkle the blanks to dry, you need to put them in an egg container or a fried egg mold.
Such blanks for apples need to be made 3 pieces
2. Now we will do the sculpting of pears. Roll the dough into a ball, pull it slightly on one side, giving it the shape of a pear.
Lightly roll the end of the pear. Insert a carnation into the wide end, into a narrow twig.
Also put in an egg container to dry.
3. Sculpt plums. To do this, cut a piece of wire 4-5 cm long. Roll two ovoids from the dough.
From fine wire cut into pieces 10 cm long, make loops at the ends.
Lubricate the loops with PVA glue and put the ovoids on the wire. With a stack in the middle of each ovoid we make a groove.
We also dry the plum in a round shape.
4. We sculpt a bunch of grapes. From a thin wire, cut pieces 10 cm long, make a loop at one end. Roll the dough into 15 balls. Put the balls on the wire.
Dry, color. You can dry the grapes by sticking a wire into a piece of plasticine.
Gather a bunch of grapes with floral tape.
5. Let our fruits dry. This usually takes 2-3 days.
6. Prime fruits with white gouache or white putty.
Colorize with paints.
Using a sponge, bring a blush to the pear.
Everything is varnished.
At the plum, decorate the bend of the wire with a floral ribbon.
7. We sculpt a vase for fruits. To do this, wrap the form cling film(for better mold removal).
Cover the dough with a film and roll out with a thickness of 0.3 cm. Using a knife, cut strips 1-1.5 cm wide and a length equal to the height of our form (I have a form height of 7 cm). You need 12 such strips.
We put the form with the wide side on the table and begin to prepare the frame for the vase. Lubricate the junction of the strips with PVA glue.
Cut rectangles with a knife, 0.7 cm high and 1 cm long. These figures will be used to decorate the edge of the vase. They also need 12 pieces.
Cut out the bottom of our vase with a knife. (The diameter of the bottom is equal to the diameter of the bottom of the form, in my case the diameter is 5 cm and the thickness is 0.7 cm).
Glue with PVA glue and smooth the bottom of our vase well.
We let the work dry completely, as a rule, it takes 1-2 days.
8. From sawdust and PVA glue, knead the batter like sour cream. We lower the brush into a mixture of sawdust and glue, with this mixture we overwrite all the seams, cracks.
Dry. Prime the vase with white gouache or white putty
and paint with paint
Carefully remove the form.
9. To decorate the vase, we blind 4 flowers and 8 leaves.
We begin to sculpt a flower. Roll 6 balls from the dough, with a diameter of 0.7 cm. We drip PVA glue onto a piece of film. In the center we place a ball, which is slightly pressed against the film.
Place 5 more balls around the ball.
With a stick with a round end (a bead put on a toothpick), we form flower petals.
In the same order, we make three more flowers.
In order to mold a leaf, you must first roll it into a ball, then flatten it. Big and index fingers sharpen the tip of the sheet. Got a leaf.
It is better to dry the flowers and leaves on the form that was used to make the vase.
Prime the flowers with white putty or white gouache.
Color the flowers and leaves.
Varnish.
10. Let's start decorating the vase. Glue "Titan" fix flowers on the vase,
