≡× MENU

• Repair
• Repair
• Interior Design
• About everything
• About plumbing

How to remove plastic wrap. How to remove sticky film from windows. Video: remove the stuck film with tape

October 14, 2016
Specialization: facade finishing, interior decoration, construction of dachas, garages. The experience of an amateur gardener and horticulturist. He also has experience in repairing cars and motorcycles. Hobbies: playing the guitar and much more, for which there is not enough time :)

Many people after installing double-glazed windows are interested in the forums - how to remove the film from plastic windows? The fact is that this operation, which at first glance is extremely simple, sometimes becomes a real problem and headache. Therefore, in this article, I will introduce you to some of the most effective ways to remove the protective film from plastic frames.

A few words about the protective film

The film on plastic windows protects the plastic surface during the transportation of windows and their installation. Moreover, manufacturers use special adhesives for gluing it, so that in the future there will be no problems with removal. However, the coating is not intended to be on the windows for a long time.

The fact is that gradually the glue under the film dries up and eats into the surface of the plastic. In addition, the coating itself is destroyed in the sun and loses its characteristics. As a result, when removed, the old film begins to tear or even crumble.

From this it can be concluded that it is necessary to remove the film in the near future, after the installation of windows. True, if the windows are cheap, then problems may arise even when removing the recently glued coating, due to the use of low-quality glue.

But, in any case, you should not despair, because there are quite effective ways to remove the old film from plastic windows, even if it has “tightly” eaten into the plastic. The main thing is to be patient and some means, which I will discuss below.

In summer, glue dries much faster and eats into plastic than in cold weather.

Film removal methods

So, the dried protective film can be removed from the surface in the following ways:

Method 1: using a scraper

First of all, try to remove the film with a scraper or other sharp object, such as a mounting or even a blade. The only thing, work with sharp tools must be very careful not to damage the plastic.

The instructions for removing the coating with a scraper are as follows:

1. first of all, you need to pry off the edge of the protective coating with a scraper or other sharp object. The unglued edge must be large enough to be grasped;
2. then you need to pull the foam and try to tear it off in one quick movement;
3. if the tape starts to break, pry it up again, but try to use as little as possible cutting tool and work more with your fingers so as not to scratch the plastic.

This method can be used if protective covering did not have time to collapse under the influence of the sun. Otherwise, it will not work to tear off the film, and it is not advisable to constantly pick it with a scraper, as it will take a lot of time, and besides, it will certainly lead to scratches on the plastic surface.

Even if you successfully peel off the protective coating in this way, there will probably be areas with glue on the surface of the plastic. You can remove them in the ways that I will discuss below.

Method 2: with an eraser

If the old coating has become easily torn or even crumbled, it can be removed with an eraser. True, this method is only suitable for small areas, for example, if there is a film or glue residue left in some places after working with a scraper.

To clean the surface, choose the most elastic band possible. With it, simply rub the contaminated area with your hands, as if you were erasing a pencil from paper. As a result, the remaining adhesive and protective coating will roll into a roller that can be removed with your fingers.

It is very difficult to completely clean the frames in this way, so it is better to use a less time-consuming method.

Method 3: hair dryer

If the coating cannot be removed with a scraper alone, you can heat the film with a hair dryer before peeling off the film. This is done as follows:

1. turn on the hair dryer at maximum power and thoroughly heat a small area of ​​\u200b\u200bthe coating;
2. then tuck in the tape and pull on the edge. After heating, the glue should become much more "pliable";
3. then heat up next section and remove it in the same way;
4. Remaining glue must be reheated and then wiped off with paper towel.

Even more effective method how to tear off the protective coating is to heat it with a steam generator. It is also mono to use a building hair dryer, however, work with it carefully so as not to melt the film, and especially the plastic frames.

I must say that this method is quite effective. As a rule, it allows you to get rid of even the most stubborn glue in the plastic surface.

Method 4: medical or industrial alcohol

Now consider how to remove the film from plastic windows with alcohol. This method is effective in removing film and adhesive residues.

The procedure is carried out as follows:

• the contaminated area should be treated with medical 96% alcohol or denatured alcohol using a sprayer or cotton solution. As the alcohol dries, it should be reapplied within a few minutes;
• then you can start removing the old adhesive and film residue with a paper towel. In the process, you may need a scraper or other tool to pry off the film.

I must say that alcohol allows not only to clean the surface of the old protective coating, but also to bleach the plastic, as well as get rid of other contaminants.

Method 5: vegetable oil

Choosing how to wipe off the remnants of the coating and glue, you can give preference vegetable oil. The last one can be anything, the only thing to keep in mind is that after the oil on the surface of the window will remain, even after you wash it. So it's best to use essential oil which smells good.

The instructions for removing the coating with this tool look like this:

1. before washing the surface, you need to apply oil to the contaminated areas with a cotton swab, then wait an hour. As the oil dries, the surface should be periodically lubricated;
2. after the specified time, the contaminated areas should be wiped off with a paper towel;
3. at the end of the work, you need to wash off the oil with a non-abrasive detergent.

Method 6: white spirit

White spirit is quite potent. The only thing before using it, wipe a small, inconspicuous area of ​​plastic with a solvent. The fact is that not all PVC windows are resistant to this solvent.

If you are sure that the solvent will not harm the plastic, do the work in the following order:

1. the edge of the film must be torn off with a scraper or other sharp object, as far as possible;
2. then the space between the film and the plastic surface should be treated with a solvent;
3. wait a few minutes before peeling off the film. After that, the tape should easily fall behind;
4. in the area where the film has not begun to tear, white spirit should be applied again.

If vapor barrier tape was used when installing the window, make sure that the solvent does not get on it, as it may deteriorate.

Method 7: "Shumanite"

"Shumanit" is a potent detergent, which is intended primarily to remove fat from the surface. However, it also does a good job with adhesives that are used when gluing a protective coating. The only thing to remember is that Shumanit contains substances that can also react with frames, so you should not apply it for a long time.

dried film and old glue removed using this tool as follows:

1. old glue should be treated with a composition. If the old coating remains on the surface, the area under it, as well as the edges along the tape, should be processed;
2. almost immediately after applying "Shumanit", the coating should be peeled off, and the remaining glue should be wiped off with a damp towel;
3. at the end of the work, the plastic surface must be washed with any suitable detergent.

Method 8: "HG Sticker Remover"

Talking about how easy it is to remove the old film, one cannot fail to mention such a tool as HG Sticker Remover. It is sold in shops household chemicals, as a rule, in vials with a capacity of 300 ml.

In general, this composition is designed to remove stickers and all kinds of self-adhesive stickers from the surface. However, as practice shows, with the help of Sticker Remover, an old protective film can also be easily removed.

The principle of its use is similar to working with other solvents:

1. before tearing off the film, you should pick it up and treat it with a tool;
2. after a few minutes, the coating can be peeled off;
3. then the surface should be treated again with the composition;
4. After a few seconds, the product with adhesive residue must be removed with a paper towel or a clean cloth.

Method 9: "Cosmofen 10"

If you ask plastic window manufacturers for advice on a protective coating remover, they will most likely tell you about Cosmofen 10, which is a mild PVC solvent designed specifically for this purpose.

You can also use its analogue, which is called "FENOSOL". The price of these compounds ranges from 300 rubles per liter.

As in previous cases, the old film is pre-tucked, after which the composition is applied. Also, these products can be used to remove adhesive residue.

Before washing the surface of the glue, you need to wait a few minutes until the product reacts.

Method 10: "P-12"

Finally, I’ll tell you about the RP-6 tool, which is acrylic thinner. With it, you can easily remove adhesive residue.

The only thing before doing the job, be sure to check if the solvent reacts with plastic frames. The fact is that some types of plastic under the influence of "RP-6" can change color.

The composition is applied in the same way as other solvents. As a rule, several minutes are enough for it to react with the old adhesive.

Conclusion

There are quite a few ways to remove the protective film from plastic windows, as we found out. The choice depends on how strongly the glue has eaten into the plastic. In some cases, it is enough to use a scraper, while in others it is simply not possible to cope with this task without a hair dryer or special solvents.

For more information, see the video in this article. If you have any difficulties with the removal of the old protective coating, ask them in the comments, and I will be happy to answer you.

October 14, 2016

If you want to express gratitude, add a clarification or objection, ask the author something - add a comment or say thanks!

To remove the protective film from plastic windows at home, you can use a solvent, scraper, hair dryer and other tools. You can also solve the problem with soap, window cleaner, brush, denatured alcohol. Next, the structure must be cleaned of the remnants of the adhesive base and the protective film. In this case, a screed, sponge, crumpled paper and special agent for glasses.

Film removal methods

According to the rules, the protective film from PVC windows must be removed within 10 days, because after a year this will be quite problematic. The film is very thin and delicate, under the influence sun rays and high temperature, it collapses and, as a result, dries up. To prevent the glue from drying out, you must use the following means:

1. 1. Blade, knife or scraper. When using sharp objects, it is important not to damage the surface. Carefully pry off the edge of the film with a scraper or blade, then tear off the rest with your hands. After you managed to peel off the protection from the windowsill or plastic window, traces of the adhesive composition may remain on the surface. You can get rid of them with a cleaning gel (Cif, for example) and a sponge for washing dishes. When removing the adhesive, no effort is needed, otherwise there is a risk of damaging the surfaces.
2. 2. Building hair dryer. The jet of hot air must be directed directly to the frame, and not to the double-glazed window, because cracks may appear on it. Under the action of heat, the adhesive composition will become softer, this will greatly simplify the cleaning of glass from the film. Similarly, you can use a regular hair dryer or steam generator.
3. 3. White spirit or other solvent. Before using any of these tools, it is worth checking the effect of the composition on an inconspicuous area of ​​\u200b\u200bthe window, window sill. If the plastic is not damaged, then you can proceed to remove the protection. How to use: gently pry off the edge of the film with a scraper or other sharp object, then apply the agent between the plastic and the film. So gradually clean the entire surface.
4. 4. Cosmophen. This is a special solvent for removing protection from PVC windows. There are 3 types that differ in the degree of impact: No. 5, No. 10, No. 20. With careless use, you can dissolve not only the film, but also plastic. Therefore, it is recommended to use the least aggressive compound number five.
5. 5. Paint remover RP6. To get rid of the old dried film, it is necessary to apply this agent on it with a thick layer. After 10-12 minutes, the surface will begin to swell. To remove the film, wear gloves and goggles. The soapy solution will help remove any remaining adhesive and product.
6. 6. Soap solution and a hard brush. This method is effective if the window is on the shadow side. Adhesive composition does not heat up much, respectively, its coupling with plastic is weak. For this it is necessary in hot water(1 liter is enough) dissolve 2 tablespoons of chips laundry soap. Wet the brush in this tool, try to wipe off the remnants of the film.
7. 7. Denatured alcohol. Pour denatured alcohol into a spray bottle, evenly spray the surface on which the protection has dried. After 5 minutes, you can pry off the edge of the film and remove it with your hands. When performing these manipulations, be sure to wear rubber gloves to protect your hands.

If the film does not come off, you can solve the problem with a detergent chemical agent(Shumanit). To clean the surface from protection, you must follow the instructions on the package. If, after removing the main part, small "islands" remain, then you can rub them with a regular eraser.

Cleaning windows from film residues

After you managed to peel off the film at home, the double-glazed window must be washed.

There are several ways and means:

1. 1. Paper, rags and window cleaner with a spray bottle. First you need to process with a damp cloth to remove the remnants of the compositions, glue and pieces of the film. After that, spray the windows with a spray and wipe them first with a dry rag, then with paper (you can use napkins).
2. 2. Sponge and screed. This option is ideal for those cases when it is necessary to reach windows. In this case, it is required to use a screed with a handle, the length of which should be within 25-30 cm. The cleaning itself is carried out as follows: first of all, you need to prepare a washing solution - 2 drops of the product per 2 liters of warm water. Soak a sponge in the solution and wring it out well to excess fluid did not drip onto the windowsill. Wash in circular motions Special attention those places where the protective film was removed and remained adhesive base. Then in the container you should collect clean warm water, wet the screed in it and run it along the entire length of the surface. After clean windows, wipe with a dry cloth in horizontal movements from left to right. At the end of these manipulations, remove water from the windowsill.
3. 3. Concentrated soap solution. To clean the surface of the remnants of the film and glue, you first need to prepare a solution from the shavings of laundry soap, then soak a rag in it and wipe the windows. When a soapy crust appears, remove it with mint. toilet paper or newspaper. To avoid streaks, use a window cleaner with a spray (Chistulya, Cinderella and others).

After acquiring an apartment, the newly minted owners are so busy putting things in order that they completely forget about the little things. The same thing happens after installing plastic windows, the frame and glass of which are covered with a protective film. After a certain period under the influence of direct ultraviolet rays, the coating begins to crack, distorting the penetration of light. Plastic parts fade unevenly, and the glue is quite firmly eaten into the surface structure. To fix problems, you need to remove them as soon as possible. protective film.

Technology for removing film from plastic windows

According to the manufacturers, the protective film should be removed within 10-12 days after the installation of plastic windows. This term due to the fact that the coating consists of two layers, which are attached to the frame with an adhesive base.

The inner part is quite delicate, for this reason it quickly collapses and begins to stick to plastic parts. The situation becomes more complicated with each passing day, forcing the housewives to grab their heads.

In case of top layer problems should not arise, it departs even after 2.5-4 months after the installation of windows.

To clean the glass and frame from glue and remove the film without harm to the product, it is important to follow the specifics of the procedure. We highlight effective methods and give practical recommendations.

Method number 1. Building hair dryer

To remove the film from the surface of the windows, you can use a building hair dryer. Purchase the device in a specialized store or a large hypermarket (Leroy Merlin, OBI, etc.). For the procedure, it is not necessary to choose a drug with several heating functions, it is enough to buy a cheap option "once".

Read the instructions, plug the hair dryer into the outlet, heat it up. In no case do not put your hand under the air flow, so as not to get burned. Direct the hair dryer not at the glass, but at plastic frame. Maintain a distance of about 35-45 cm so that the film does not melt.

Under the influence high temperatures the adhesive base will soften, which will allow you to easily remove it from the surface of the windows. Pry off the free edge, walk over the surface with the terminals with a hard cloth soaked in acetone or car enamel thinner.

Method number 2. Scraper

A kitchen scraper will help to remove the film from the surface of plastic windows, which is used to clean enameled and glass-ceramic stoves. The tool is sold in Everything for the Home stores; it is a spatula with or without a rubber tip.

To use the tool correctly, pry the free edge of the film with it, pull it slowly and at the same time help yourself with a scraper. Move along the inner (adhesive) part of the film, avoid breaking the protective material.

When the procedure comes to an end, inspect the glass and frame for the presence of glue. At a positive result spray window cleaner over the entire surface, leave for a quarter of an hour, constantly updating the composition. When the glue dissolves, remove it with a scraper.

Method number 3. stationery eraser

The option is rightfully considered ineffective if the film is on the windows for a long time (about 2-3 months). To remove the adhesive, purchase several school erasers. The main thing is that they are clean (no traces of ballpoint pen or pencil).

Before proceeding with the procedure, make sure that the surface to be cleaned is perfectly dry. Next, start rubbing the remaining glue with an eraser, rolling them into oblong lines. Proceed step by step, process individual zones in turn (about 5-10 sq. See).

To increase efficiency, you can spray a thinner for paints or car enamels on the frame and glass, nail polish remover, pure acetone is also suitable.

Method number 4. "White Spirit"

An excellent option for removing the protective film from plastic windows is a building hair dryer in combination with white spirit. Heat the surface of the frame from a distance of 40 cm, pick up the edge with a scraper, then gently begin to pull the film away with your hands.

When you have separated about 10 cm, spray White Spirit with a spray bottle onto the adhesive surface. Clean the base with a gauze cloth or scraper, gradually move down.

After removing the protective coating on the glass and frame may remain sticky marks. Wipe them with a hard cloth soaked in white spirit, if desired, use a scraper with a rubber tip.

Method number 5. "Cosmophen"

Firms for the sale and manufacture of windows produce a tool called "Cosmofen". The main task The drug is the cleaning of metal-plastic structures from adhesive formations after removing the film. The drug is produced different concentration, it all depends on the number of active components in the composition.

"Cosmofen" marked "No. 5" is considered the most effective, but it is able to dissolve plastic, for this reason it is recommended to be careful. Preparations under the number 10 and 20 are also produced, it all depends on the duration of exposure of the film on the glass.

To use the composition correctly, it is important to follow the manufacturer's recommendations. As a rule, after removing the film, the mixture is sprayed over the entire surface, and then gently removed with a cloth or scraper.

When working with the composition, be sure to wear goggles, a mask, gloves. If possible, use a long sleeve robe.

Method number 6. Blade

Perhaps one of the most common options is to remove the film sharp knife or blade. To do this, just pick up the free edge, and then gently pull the film at an acute angle. It is possible that it will break, do not rush.

You can remove the remaining glue with a blade. The main thing is to pre-moisten the surface with any agent that contains a solvent. Acetone, white spirit, industrial solvent, nail polish remover, etc. are suitable.

Do not apply pressure on the blade to avoid scratches. After removing most of the adhesive, wash the windows with dish soap and a hard sponge.

Method number 7. Paint remover

Purchase a paint stripper called "RP-6" from a hardware store. Pry off the free edge of the film with a knife or blade, gently pull it down at a sharp angle. Next, apply "RP-6" on the entire surface of the adhesive base, soak for a quarter of an hour (the exact time is indicated by the manufacturer on the package). Protect your hands while handling the product Airways and eyes.

Remove excess with a dry rag, prepare a solution. Grate half a bar of laundry soap, dilute the chips in 3 liters. boiling water, stir. Moisten a cloth, wipe the glass and frame until the glue disappears completely.

It is easy to remove the protective film from the surface of plastic windows if you use effective methods. Consider cleaning the adhesive with white spirit or industrial solvent, remove it stationery eraser, blade, Cosmofen or RP-6. Observe safety precautions.

Video: how to remove the old protective film from PVC windows

Many users, faced with the problem of a window film firmly “soldered” with a PVC profile, are in a hurry to experiment, which does not always end well. Especially in the case of colored windows, there is a risk of destroying them. How to effectively and without disastrous consequences remove the old protective film from plastic windows, the WINDOWS MEDIA portal will tell.

All plastic windows come on the market with frames protected by the manufacturer with a self-adhesive film. By law, the protective film should be removed as soon as possible after the installation of the windows is completed - especially when the PVC window is exposed to direct sunlight.

Why is it so difficult to remove the old protective film from PVC windows?

Unfortunately, it happens quite often that due to the negligence of the installers or the user himself, the protective film on the PVC profile can remain even for several years. In this case, when the hands reach the point of putting the new plastic windows in order, the user will be in for an unpleasant surprise - it is almost impossible to remove the protective coating.

It is difficult to remove the old window film from the profile of a plastic window, because it consists of two layers. The outer layer (transparent film) begins to peel off under the influence of ultraviolet rays and is relatively easy to clean. But at the bottom there is a second layer of white plastic with markings - it is he who adheres so strongly to the substrate.

Particularly bad is the presence old film looks in the case of a tree-like profile, because usually a protective coating is used white color. Under the influence of UV rays, the film undergoes vulcanization and adheres very firmly to the surface of the PVC window. At the same time, it becomes less durable and breaks easily.

Some try to wash off the protective layer with gasoline, acetone or other solvents - this helps a little, but in parallel, you can remove the wood texture that is applied to the frame lamination (white PVC windows are, of course, insured against this). Experts do not recommend exposing the surface of a colored PVC profile too strong mechanical impact (scraping or sanding), because it is very easy to damage the lamination layer.

Eureka: there is a way to get rid of the old protective film!

Fortunately, there are several ways to get rid of the protective film, we suggest considering one of them. This method is simple, effective and, most importantly, will not destroy the plastic window. However, the procedure will take quite a long time and will require the use of a device with a steam cleaning function.

Such a device can be bought without problems, they are often sold in supermarkets. Please note that the package includes a special hose that allows you to fix the nozzle. Versions of this device often appear on the market, in which steam exits directly from the tank through a nozzle. In this case, you will have to constantly hold the heater in your hands during cleaning, but it will soon become clear that heating the film in the lower part of the frame is impossible in this case (the window sill interferes).

Work begins with filling the purifier with water and connecting it to the mains. After a few minutes, you can start heating small area protective film with a jet of steam (hold the nozzle directly over the film or even touch it). Heat up a small piece of 1-2 cm across the entire width. If the window film is already too old and not peeling off, you will need to reheat it (after it has cooled down). At this time, you can heat the protective coating of the window from the other end.

To remove the protective film with steam, shortly after heating a small area, you should try to separate the film from the substrate with your fingernail. This must be done carefully and slowly, across the entire width of the tape. This is the most important point. It is necessary to make sure that a small piece of the film is peeled off across the entire width. Then you can grab the end and slowly (!) tear off the film with parallel heating with steam from above and below (at the points of contact with the substrate).

If the protective film begins to tear and its fragment does not come off, you need to use a fingernail in this place and lead to a situation where it will peel off again over the entire width. After removing a sufficiently long fragment, cut it off with scissors, leaving 2-3 cm so that there is something to catch on to continue further cleaning the PVC profile.

After removing the protective layer on the surface window frame remains white coating, which is quite difficult to wash off. And here there is a proven way - you can use a glass cleaner for this purpose (for example, Mr. Muscle).

When buying new plastic windows, do not ignore the advice of the window company, which is clearly stated in the instruction manual, when it is worth removing the protective film from the PVC profile. This will save you both time and money, and save your nerves. In general, compliance with the manufacturer's recommendations, not only in this paragraph, but also in all others, is the key to the impeccable appearance and durability of your plastic windows.

New plastic windows have a coating that many people take a while to remove. Over time, it dries out, so getting rid of it becomes difficult. How to remove dried film from plastic windows without damaging them?

How to remove film from plastic windows

Why does the protective film need to be removed immediately?

New plastic windows have a film that protects them from dust, dirt and damage in the form of scratches. By design, it is two-layer and is glued to the window using special composition. Under the influence of sunlight, the inner layer of the coating is destroyed and sticks to the plastic. Every day the film becomes more and more difficult to remove.

How to remove protective film from plastic windows

For this purpose, several methods are used: mechanical (using tools) and chemical (household mixtures).

The first ones include:

Scraper for cleaning glass-ceramic surfaces. It can be used to remove the protective coating. And then remove the traces of the paste with a window cleaner. The scraper must be handled carefully, as it leaves scratches.

Industrial dryer. It can be replaced with a regular one. First point the device at the film (hot air will peel it off) and then stationery knife scrape off the leftovers.

Not less than effective way– use of a steam generator. The principle of operation is almost the same as that of a hair dryer.

An ordinary eraser will also help to cope with the problem.

Mechanical methods remove the protective coating, and adhesive residues are easily removed with either a cleaner or an acrylic solvent.

Chemical methods:

Denatured alcohol. Pour a few spoonfuls into a flower sprayer and spritz over the coating. After a few minutes, tear off the film with a knife.

Paint remover. Apply the composition to the surface and wait 10 minutes. Over time, the coating will begin to swell and easily be removed from the window.

Using chemical compositions work should be done with gloves so as not to damage the skin. It is also recommended to wear goggles for safety.