Putty vgt "extra" on pine wood. Wood putty vgt Acrylic wood putty vgt extra
Putties with acrylic resins as a binder perfectly pass water vapor and have modifications for both indoor and outdoor use.Most often putty is used for interior decoration. If the room has normal humidity air, then a standard putty for work is quite suitable for it. This material can be applied to concrete, brick, stone or plaster walls in rooms that will not long period be without heating. This white aligns the walls and ceilings for further painting or wallpapering.
Slits, cracks and potholes up to 7 mm can be leveled in one layer, and larger irregularities are smoothed out after applying the next layer over the hardened bottom. This ready composition it does not need to be diluted with water, and it should only be applied at a temperature not lower than +7 C. It cures completely after 24 hours and shows a slight shrinkage in thickness. The same composition with a slightly higher viscosity is produced in the Profi series.
Universal putty for external and internal "VGT" shows excellent adhesion to different types surfaces: concrete, brickwork, cement or plaster, a natural stone and even glass. This material is moisture resistant and is not afraid of low temperatures. Therefore, such a composition can be used both for the facade and indoors with a "dry" and "wet" mode. Since the finished composition contains water, it can only be used at a temperature not lower than +5 C, so that it has a working viscosity, although in the hardened state it is resistant to frost up to -40 C. Such a coating is moisture resistant, passes water vapor through itself into direction of lower concentration, which supports comfortable conditions indoors. the material can be topcoated after priming. It fills irregularities and gaps up to 7 mm deep in one coat.
Acrylic grout for between or granite tiles, as well as between other decorative coatings, withstands the effects of low temperatures and precipitation, therefore it is successfully used for both indoor and outdoor work. This material extends the life of the finish and does not allow moisture to get under or porcelain stoneware. putty on acrylic is somewhat more expensive because it contains modifiers that make it weather resistant. It is also used for internal works in rooms with high humidity or in critical places that are exposed to moisture. In addition to mineral bases, this composition also exhibits excellent adhesion to wood. This grout also shrinks a little, but the surface is as smooth as it was after application. It cures in 1 day and is an excellent base for most decorative facade materials.
Wooden surfaces are processed in the carpentry shop, but they do not always have an ideal flat surface, which is needed for painting and other types of finishes. Cracks in wood, holes from knots and other irregularities can be repaired with a special acrylic putty "VGT" for wood. It is moisture resistant and can be used inside and outside the building. This is another use of acrylic binder, thanks to which this Russian creates many varieties of its products.
Wood putty, vgt extra
This putty can be used as a finishing putty, in particular in rooms with high humidity or on surfaces that sometimes come into contact with water.
Properties that characterize this putty:
High resistance to water;
Hardness and strength;
It shows itself excellently in such works as sealing knots, cracks and other shortcomings in joinery;
Gives the surface the color of raw wood;
Shelf life: twelve months.
Surface preparation:
Before starting work, it is necessary to prepare the surface in the proper way. It must be dry and clean. If there are peeling coatings, they must be removed.
Application method:
This putty should be applied with a spatula in a continuous layer. The recommended thickness of one layer should be about one millimeter. It is also possible to close up irregularities with a depth of up to two millimeters. If the irregularities are large enough, then a multi-layer coating is necessary. After application, after a period of time from three to five hours, it is necessary to carry out sanding.
Specifications:
Complete drying occurs after twenty-four hours in normal and at a layer thickness of two millimeters. The release time is two hours.
Dry residue is not less than seventy-two percent.
1.65-1.75 grams per cubic centimeter.
Storage:
Store in a sealed container, temperature regime from zero to thirty degrees. It can also be stored at temperatures up to minus forty degrees, but not more than 1 month. or five freeze-thaw cycles.
This type of putty cannot be applied to the surface if the humidity in the building is above average and the temperature is less than seven degrees.
Strength with uniform separation: not less than five kilograms per square centimeter.
Consumption: from half a kilo to one kilogram, four hundred grams per square meter.
Varnishes and paints - paint and varnish production. varnishes and paints from the company OOO "VGT Enterprise"
High quality. All varnishes and paints "VGT" and "BAU MASTER", including interior paints, facade and other products, are certified and manufactured according to specifications. Documents certifying the compliance of varnishes and other products with the quality management system, conclusions (hygienic, sanitary-epidemiological, fire safety) and test reports are presented in the "Certificates" section.
A wide range of. Our company is one of the three leaders in terms of production of paint and varnish products in Russian market. The assortment includes more than 200 items for all types of repair work.
Developed dealer network. Our company has a large dealer network: VGT and BAU MASTER paint and varnish products are represented in 73 regions of Russia and 6 CIS countries.
VGT Enterprise LLC - wholesale at competitive prices!
Putties ready and for wood VGT
Universal acrylic putty VGT
1kg, 1.7kg, 3.6kg, 7.5kg, 18kg
Putty for exterior and interior works For leveling and sealing irregularities up to 7 mm deep.
Wood putty VGT
Assorted colors
Packing 0.4 kg, 1 kg
Fine-dispersed putty for sealing knots, cracks, other surfaces and other important work.
Acrylic putty for interior work VGT
Packing 1.7 kg.
For interior work in dry rooms. Serves for leveling surfaces and sealing joints up to 7 mm deep .
Acrylic facade putty VGT
Packing 3.6 kg, 7.5 kg, 18 kg
For front and responsible internal works. Serves for leveling surfaces and sealing irregularities up to 7 mm deep.
Textured putty VGT bucket
Packing 9 kg, 18 kg.
Highly viscous, coarse textured material for obtaining a decorative, embossed coating on concrete,
brick, plastered and other types of surfaces.
ROLLER medium
Packing 9 kg, 18 kg.
Textured material with natural filler for a relief coating.
medium-grained (grain size - 1.5-2mm).
VENETIAN PLASTER
Packing 8 kg, 16 kg
"vgt extra" on wood
"VGT Extra" wood putty
Fine-dispersed putty for sealing knots, cracks, other wooden surfaces and other responsible work.
Can be applied as finishing putty, incl. in places with high humidity or in periodic contact with water; high moisture resistance, hardness and strength; recommended for sealing knots, cracks and other defects in joinery; imitates the color of raw wood; warranty period of storage is 12 months.
Surface preparation: The work surface must be dry and free from contamination. Peeling old coatings must be removed. Strength at uniform separation Not less than 5 kg/cm². 0.5-1.4 kg/m² Method of application Putty is applied with a spatula in a continuous layer. Optimal Thickness applied layer of putty about 1 mm. It is allowed to seal irregularities up to 2 mm deep. For large irregularities, a multi-layer application of putty is recommended. Sanding should be done 3-5 hours after application. Drying time To touch 2 hours, completely dry in 24 hours under normal conditions (with a layer thickness of 2 mm). Dry residue Not less than 72%. Density 1.65-1.75 g/cm³
Storage In a tightly closed container at temperatures from 0°С to +30°С. Storage at temperatures up to -40°C is possible for no more than one month or five freeze-thaw cycles. Not recommended Apply at high humidity and temperatures below +7°C.
Fine-dispersed putty for sealing knots, cracks, other flaws in wooden surfaces and other important work.
- high moisture resistance, hardness and strength;
- recommended for sealing knots, cracks and other defects in joinery;
- imitates the color of raw wood;
- can be used as finishing putty, incl. in places with high humidity or in periodic contact with water.
PROPERTIES AND FEATURES
Low-shrink putty, after drying does not grind, gives a durable smooth matte surface. Provides high water resistance, hardness and durability of the coating. The putty contains a finely dispersed filler, so it can be used as a finish. Available in several colors: “white”, “birch”, “pine”, “oak”, “beech”, “mahogany”, “larch”
APPLICATION AREA
For sealing knots, cracks and other defects in wooden surfaces, as well as for other responsible finishing works on fiberboard, MDF, chipboard, concrete, brick, plaster, etc.
Water dispersion of polymer, pigment, filler, modifiers.
TECHNICAL DESCRIPTION
Tensile strength at uniform separation, kg/cm²: Not less than 5 kg/cm².
Surface preparation: The work surface must be dry and free from contamination. Peeling old coatings must be removed.
Consumption: 0.5-1.4 kg/m²
Method of application: Putty is applied with a spatula in a continuous layer. The optimum thickness of the applied putty layer is about 1 mm. It is allowed to seal irregularities up to 7 mm deep. For large irregularities, a multi-layer application of putty is recommended. Sanding should be done 3-5 hours after application.
Drying time: Tack free 2 hours, completely dry in 24 hours under normal conditions (2 mm layer thickness).
Dry residue: Not less than 72%.
Density: 1.65-1.75 g/cm³
Storage: In a tightly closed container at temperatures from 0°С to +40°С. Withstands freezing down to -25°C, but not more than five freeze-thaw cycles. Shelf life 18 months from the date of manufacture.
Putty VGT "Extra" for wood SOSNA - finely dispersed putty for sealing knots, cracks, other wooden surfaces and other important work.
Properties:
- high moisture resistance, hardness and strength;
- recommended for sealing knots, cracks and other defects in joinery;
- imitates the color of raw wood;
- can be used as a finishing putty, incl. in places with high humidity or in periodic contact with water;
- maintains freezing to -40 °C no more than one month or five cycles of freezing-thawing.
Surface preparation: The work surface must be dry and free of dirt. Peeling old coatings must be removed.
Strength at uniform separation: Not less than 5 kg/cm2.
Consumption: 0.5-1.4 kg/m2.
Application method: The putty is applied with a spatula in a continuous layer. The optimum thickness of the applied putty layer is about 1 mm. It is allowed to seal irregularities up to 7 mm deep. For large irregularities, a multi-layer application of putty is recommended. Sanding should be done 3-5 hours after application.
Drying time: Tack free in 2 hours, completely dry in 24 hours under normal conditions (with a layer thickness of 2 mm).
Dry residue: Not less than 72%.
Density: 1.65-1.75 g/cm3.
Storage: In a tightly closed container at a temperature from 0°С to +30°С. Storage at temperatures up to -40°C is possible for no more than one month or five freeze-thaw cycles.
Packing: 0.3 kg; 0.45 kg; 1 kg; 50 kg.
