How to make a soap dish with your own hands. Homemade soap dish for liquid soap How to make a soap dish with your own hands
How to make a soap dish with your own hands from improvised material, which can always be found in household mess.
When designing such a product, and then in the future and its manufacture, one should always be guided by the following requirements:
Minimum number of parts
ease of manufacture
use of moisture resistant material
soap protection external environment, or in other words, provide a cover in the design of the soap dish
appropriate appearance
The isometric figure shows the assembly diagram of the box and its detailing.
1.
Side wall.
2.
Back wall.
3.
front wall.
4.
Bottom.
5.
Cylindrical metal pin 3 x 20 (mm).
Reference:
Cylindrical metal pins can be made from ordinary construction nails of the appropriate diameter.
SIDE WALL
LID
Specification of material dimensions (length, width, thickness):
Back wall 130 x 40 x 10 (mm)
front wall 150 x 50 x 10 (mm)
bottom 130 x 90 x 10 (mm)
The material used for the manufacture of the washbasin soap dish is moisture-resistant plywood with a thickness of 10 (mm).
How to make a soap dish with your own hands for or manufacturing technology:
1.
Cut out blanks from plywood, strictly observing their dimensions, parallelism and perpendicularity of the faces.
2.
Mark the center of the pin holes.
3.
Drill holes to the desired depth.
Reference:
The centers of the holes in the parts to be joined must exactly match. Holes are drilled strictly perpendicular to the edges, otherwise assembly may be difficult. It is best to use a metal jig when drilling, which you can make yourself.
4.
Insert the pins on the adhesive into the holes in the side walls of the soap box.
5.
Connect the back and front walls, the bottom with the side walls into pins for glue.
6.
Squeeze the assembled box with clamps and allow the glue to dry.
7.
Smooth out the sharp edges of the box and finish from the least visible parts and finish with the front surfaces.
8.
Surface finishing. Apply a thin layer of varnish with a brush. After drying, treat the surface with fine sandpaper, then wax the surface.
9.
Install cover on pins 3 x 20…30 (mm)
To make it, we need:
Transparent plastic bottle;
Pencil;
Ruler;
Making a soap dish
First, rinse and dry the bottle. Put the bottle and soap next to each other. This will help you decide how long the future soap dish will be.
Draw two lines on each side with a pencil on the edges of the jar.
These stripes that you will draw will serve to form the legs of the soap dish. Their width should be about one and a half centimeters. In order to draw the lines, you can use a ruler or a soft tape measure so that they are even and straight.
Cut off the bottle with a knife. Cut the bottle with a knife into two halves along the glued seam. After that, one of the halves must be cut off at the edges, cutting off the bottom and neck. Cut along the outer lines. After the blank is partially ready, cut the bottle along the inner lines, cutting out short strips. Thus, you will have two legs and the rounded stand for the soap dish itself.
Now place the base on a flat surface and apply glue to its edges, to the bottom. Glue the legs. To be honest, at first I would recommend putting the legs on any flat surface, and only then put the base on top of them. This method will help to glue the legs to the soap dish so that everything is even and that it does not stagger.
Now it remains only to let the glue dry, and that's it, the soap dish is completely ready.
 |
|
If you urgently need to add a touch of spice to, then try to quickly make a soap dish with your own hands. This is a creative process, with its own approaches, so wake up the cockroaches in your head and get down to business.
What materials may be needed?
- plastic bottle;
- gypsum powder or polymer clay;
- glue "Moment";
- paints for plastic and plaster.
It’s impossible to quickly make a soap dish with your own hands!
If you want to reinvent the wheel, then you shouldn’t: it has already been invented before you, but please invent the soap holder! Below is a photo of what the craftsmen did. Learn from experience or try to design something special, not like what you saw. True, in 5 minutes you will not make such a masterpiece, but in 15 - real time for creativity, if at hand for this there is essential tool and patterns are ready.
Soap dispenser from a plastic bottle
In addition to stands for a solid piece, you can also, for example, build a dispenser for a liquid detergent consistency in the country. Do you like this option? Then decide where you will start work.
By the way, such a dispenser may well carry 2 more loads: act as a holder for toothbrushes and be a stand for toothpaste or mouthwash.
Soap-swallow
When you urgently need to collect your husband on the road late at night, and there is no soap dish, as if it were a sin, then 2 bottoms from under a plastic bottle help out.
- Cut off the bottom so that the soft walls protrude 5 cm up.
- Find an unnecessary zipper for clothes in the house.
- With wide stitches, sew a zipper to the edges of both plastic bowls.
- You get a nice soapbox-swallow.
DIY soap dish from the bottom of small bottles
You can make a flower soap dish from a plastic bottle day, but you only have to paint the cut object in the color you need. Pick up the paint in the store, just make sure that it is not afraid of water: it is best to choose enamels in spray cans for the car.
Gypsum soap dish
The most openwork soap dish is a gypsum soap dish, but it can only be used for decorative purposes, since gypsum is afraid of water and quickly collapses from it.
21 chose
For several months I admired the soap brewed and presented to me Any. When it came time to try all this "yummy" I thought about how and in what to store small masterpieces. Simple soap dishes are of the wrong shape, and it’s not interesting to put a hand-made exclusive in a simple purchased plastic. And I decided to make my own "soap dishes" for each bar of soap.
I already had some experience in creating Christmas balls from plastic bottles from water. And the material seemed suitable to me, besides, it happens different colors. Here's what I ended up with...
Green leaf
I made it from the side of a green bottle. First, we prepare a large rectangle by cutting stationery knife bottle along the seam and cutting off both edges. Then, with ordinary scissors, we cut out the desired shape of the future sheet. In the final, hot air treatment is needed to deform the material as we need. To do this, hold the product high above the gas burner or just above the lighter. When starting heat treatment, it is important not to overheat, so as not to get burned, and only slightly bend all pointed edges without touching the middle - there will be a bed for soap. Any rectangular or elongated piece can be placed in the finished soap dish.
Pink shell with a pearl
Some water bottles have a ribbed surface that resembles the pattern of a shell in which a pearl grows. The shape of the neck of such a bottle (especially if it Pink colour), pretty much everything you need. Cut off the neck, cut off forming a wavy line along the edge of the "funnel". We divide diagonally into two parts (leaving only the connection at the very base). For greater similarity, both halves need to be flattened a little, for this we put the blank under the press for a couple of hours (for example, under a stack of magazines). We process only the very edges with hot air, to form a smooth and non-sharp line. In the final, it would be nice to cover the top "lid" with mother-of-pearl with inside, lower from outer. I didn’t have real mother-of-pearl, but I had a good pink mother-of-pearl varnish. After drying the shells, it remains only to place a soap "pearl" in it.
floating water lily
A water lily is made from the bottom of a bottle. Cut off the whole circle with a clerical knife above the legs by 2 cm. Then we move on to heat treatment. Gently hold, heating the inner surface of the edge. If you heat evenly from all edges, the water lily will turn out to be even. You can already use. Moreover, not only as a soap dish, but also as a floating decoration, and even as a candlestick for a heating or other small candle.
Box with bows
We draw a rectangle on the bottle with adjacent rectangular sides. Cut along the outer edge, bend and sew adjacent edges with beautiful threads. We tie knots and bows at the ends of the threads. It's good if some pattern is embossed on the bottle - pigeons "sit" on the sides of my soap dish.
Do-it-yourself soap dish - an original element of the interior of the kitchen and bathroom, attracting the attention of others unique design. Against the background of high-tech analogues equipped with a touch screen and magnetic holders, unusual accessories in the form of shells, rosebuds and wicker boxes look especially elegant. Exclusive Items household, designed to accommodate soap, in tandem with other homemade parts furnishings - towel holders, shower curtains and rugs will allow you to create an individual interior genre for decorating a room for ablutions.
The original do-it-yourself soap dish is ideal for arranging not only bathrooms in the house, but also for decorating a washstand or a summer shower room located on the territory personal plot. If you are planning to make a soap holder designed for use on fresh air, then it is necessary to select raw materials that can withstand intense exposure to ultraviolet radiation and gusts of wind. Due to the continuous contact with water, to create beautiful accessories, it is necessary to use materials that have excellent moisture resistance and hygroscopicity. As a result correct selection raw materials and decorative elements You will be able to make a stylish and functional accessory.
Selection of materials for creating coasters for soap
A do-it-yourself soap dish allows you to add a personal touch to the design of shower rooms. In order for it to organically blend into the canvas of the stylistic concept, it is necessary to correctly select the basis and Decoration Materials to create an original piece of furniture:
- If the bathroom is done in a manner mediterranean style design, it is necessary to use shells, pebbles, river sand, dried algae, starfish and other themed decorations to decorate the decoration item.
- If the ablution room is decorated in the traditions of country, chalet, ethno, colonial or eco-style, then preference should be given natural materials, embodying natural motifs: branches and log cabins of trees, dried flowers, acorn caps, sunflower or pumpkin seeds.
- If the shower room is decorated in a loft style, then you should pick up non-trivial items to decorate the bathroom soap dish: fragments drainpipe, clinker brick or an unhewn board.
Unique do-it-yourself soap dish from improvised materials for a long time will not lose its spectacular original appearance if its outer part is covered with quick-drying varnish, and the inner cavity of the container is decorated with a moisture-absorbing gasket. If you want to place this accessory on a wall or any other flat vertical surface, then you should make a magnetic soap dish with your own hands or equip it with strong suction cups. Magnetic holders are able to withstand a heavy base with soap, and silicone suction cups are able to withstand light products made of plastic or any other polymer.
When selecting materials for creating a soap holder, you should study them in detail. operational properties, since moisture is incompatible with polymer clay, metal and wood. These types of raw materials can be used to decorate decor items designed to decorate the interior of a restroom, bath or kitchen.
Hand-made lessons on creating interesting interior accessories
A do-it-yourself soap dish will emphasize the talented abilities of the owners of the house and will become a noteworthy piece of furniture. Most in a simple way creating an exclusive soap tank is the use of plastic containers. These junk household items have high plasticity and moisture resistance. Therefore, they are great for creating a variety of decor items: planters, garden figurines, food dispensers and containers for storing various things.
To make a beautiful flower-shaped tank with wide open petals, you need to prepare the following materials:
- flaming gun - gas burner, which allows you to easily and quickly modify the shape of the plastic;
- container from under mineral water or carbonated drink;
- sharp scissors;
- ruler;
- green acrylic paint yellow color;
- a thin and wide brush with medium hard bristles made of squirrel hair.
From one plastic container, you can make two accessories for the bathroom - a reservoir and a dispenser designed to accommodate soap in liquid and solid states. As a result of the execution step by step instructions you will be able to make an original soap dish with your own hands, the photos of which can inspire true connoisseurs original accessories interior to complete a simple master class:
- Cut a plastic bottle into two halves. The lower part should be used to create a stand, and the upper fragment of the container should be used for the dispenser.
- Measure 7 centimeters from the bottom of the bottle with a ruler and make a mark on the plastic surface.
- To the marked line, cut out the leaves of the flower of a triangular oblong shape. On sheet-like elements, it is necessary to make cuts diagonally on both sides.
- Make small incisions in the mark area, where at the final stage of the decor it will be necessary to carefully place the acute-angled end part of the flower leaves.
- Using a flaming gun at a distance from the bottom of the container, it is necessary to give plastic container the shape of the curved petals of the inflorescence.
- All parts of the product must be coated with green and yellow paint. After the paint has dried, you need to cover the soap holder with acrylic varnish.
Before you make a soap dish with your own hands, you should determine the size of the tank corresponding to the free space on the bedside table in the restroom or shelf hanging shelves In bathroom. If there is not enough free space for its placement, it is necessary to supplement the product with silicone holders or magnets.
An alternative way to decorate this bath accessory can be the transformation of a ceramic flower stand. It will act as a base, which should be decorated in a chaotic manner with multi-colored fragments of ceramic or facet tiles. To fix them, use tile glue and tweezers. As a result, it will turn out to make an interesting accessory with a mosaic ornamental design.
DIY soap dish is a great gift for friends, colleagues and relatives. This practical item is an indispensable attribute of the bathroom and shower room. The Westwing Shopping Club has a large collection of various stylish accessories interiors made from quality materials.
