• Repair
• Repair
• Interior Design
• About everything
• About plumbing

What to make a frame for a mosquito net. Mosquito nets with their own hands. Mosquito net installation procedure

Summer brings not only positive emotions and relaxation, because you should not forget about annoying flies and dangerous mosquitoes, who strive to fly into the open window. mosquito net it is inexpensive, but if you calculate that there are several windows in the house, then in the end you get quite a decent amount, which, if desired, can be saved. Do-it-yourself mosquito net is done quickly and will be inexpensive.

Which is better - a purchased mesh or made by yourself?

Buying a window mesh will cost you about 1500-2000 rubles, so for the sake of savings, you can make it yourself. Many people ask the question - how to make a mosquito net on a window? It is not difficult, especially since everything you need can be bought at a hardware store. If you are interested in the question of what mosquito nets are made of, then the answer is simple - the material is durable fiberglass with the addition of weatherproof PVC. The higher the quality of the material, the higher the protection against insects.

Before you make a mosquito net with your own hands, take careful measurements, do not forget about allowances. If you are going to attach the mesh with Velcro or glue, choose something that can be easily removed without damaging the window.

A few simple ways to make a mosquito net with your own hands

There are two types of mosquito nets that you can make yourself:

1. Fastened with fastening tape - simple and cheap way make a mosquito net with your own hands.
2. Framework.
3. Roll.

One of the easiest ways to make a mosquito net with your own hands is with the help of special material and adhesive tape.

Take high-quality Velcro, the quality of attaching the protective mesh to the window opening will depend on this. You will also need special material with small cells. The smaller the cells, the better. Such material can be purchased at fabric stores, or you can use old products, for example, unnecessary tulle. It is best to purchase a special mosquito net - it reliably protects against insects and withstands atmospheric influences.

Mosquito net fixed with adhesive tape

After all measurements are taken, take the material and cut it, do not forget to leave small allowances. Velcro divide into two equal parts. Apply glue to one part and carefully glue it to the window opening. After the glue has dried, attach the mosquito net to the adhesive tape. Similar grids can be made for a car. Done quickly and easily with minimal cost. Instead of sticky tape, special magnets can be used, this will significantly reduce the installation time of the grid and simplify the process.

Frame window grids

more costly and complex method manufacturing mosquito nets, is a way to mount on the frame. To do this, you will need metal corners, plastic cable and rivets.

The first thing to do is to measure the window with outer side, because it is there that the mosquito net will be attached. On the cable, cut the desired length, adhering to the angle of 45 degrees. Sand the slices and connect with metal corners. Now make holes in the corners in which the rivets will be located. They should be outside, not inside the cord. Now it remains to fix the mosquito net itself on the frame. Do not pull the mosquito net too tightly, as this can deform or tear the canvas.

Frame window grids

You can make sliding mosquito nets with your own hands, they will fit well and protect the balcony opening or front door. Mosquito net on the balcony will help you prevent penetration dangerous insects indoors, it will reliably protect even from street dust. The manufacturing technology is the same, the only difference is that the material is cut in the middle, the edges are processed. For convenience, you can attach magnets or rivets to the edges of the mesh, so you provide additional protection.

Roll mosquito net

Rolled mesh window operates on the principle of roller shutters. It will reliably protect against insects, and it is convenient and easy to use. If you are interested in how to assemble a rolled mosquito net with your own hands, then there is nothing complicated here. You just need to be patient and have the right materials.

With your own hands, you can make a mosquito net for a window of any size. To make a rolled protective mesh, you only need a special box with a shaft and material. To attach the mesh to the window, use special magnetic latches. You can apply fastening with screws with an overlap or at the end of the guide in the opening to the slope. It is more convenient to use a rolled mesh than a regular one, and it is much easier to care for it.

Roll mosquito net

Rolled mosquito net on the window is an excellent protection against annoying insects. Allergy sufferers will especially appreciate this design - after all, it will protect the room not only from mosquitoes, but also from plant pollen and poplar fluff. The material for such a mesh is best to choose fine-grained, this will increase the level of protection.

Making a mosquito net with your own hands is not difficult. If you need a mosquito net for a balcony or window, you can make it yourself quickly and without extra costs. Give this process a few hours and enjoy a quiet life without annoying insects! A handmade mosquito net is quite inexpensive. After the summer, it can be removed from the window and carefully packed, and next year it can be hung again on the window.

Homemade and the cheapest option for making a mosquito net without using a frame. This option is to attach the mesh directly to plastic profile window.

Mosquito nets are firmly established in life modern man, as they are able to reliably protect against the penetration of insects into the room. Their only drawback is high price. Therefore, the owners country houses tend to make it yourself from improvised materials. Installing a mosquito net on a plastic window with your own hands does not cause any difficulties.

Do-it-yourself mosquito net from a cable channel

A do-it-yourself mosquito net from a cable channel is a great alternative to a store-bought one.

Mosquito nets produced in factories are practically invisible, do not prevent penetration into the room fresh air and light. At the same time, they well block the path for dust and insects. Mosquito stacks are durable, easy to install. When buying plastic windows, the owners of apartments and houses must also purchase them.

Considering high cost such a design in the collection, many have a natural desire to do everything on their own. Also, if the window has custom sizes or shape, manufacturing design according to custom order will cost even more and the waiting period may surprise impatient customers. All these difficulties can be avoided if all these problems are solved without outside help.

We offer you to get acquainted with the types of mosquito nets that are sold in Russia, namely:

• swing;
• sliding;
• pleated;
• rolled.

Each type has its own advantages and disadvantages. For example, pleated and rolled mosquito nets do not require dismantling for the winter and they are quite compact, but they are expensive. Swing and sliding take up space from the room, so many refuse to use them.

Pictured frameless mosquito net

A do-it-yourself mosquito net from a cable channel is an excellent alternative to a store-bought one, and in terms of quality and durability it is in no way inferior to the factory version. For the manufacture of the structure, it is necessary to purchase the following materials:

1. cable channel right size.
2. Grid.
3. Metal corners.
4. Rivets.

Video on how to make a mosquito net from a cable channel with your own hands:

Installing a frameless mosquito net on a plastic window with your own hands, video

Resourceful craftsmen have found many alternatives to the traditional mosquito net. For example, meshes on tapes for fastening are very popular. How to make such a design yourself? To do this, you should purchase such details, namely:

• insect net with small cells;
• sticky tape;
• glue.

Before installation, the plastic window is thoroughly washed. Now we need to do the markup. To do this, the window is inspected and markup is performed. It is worth choosing a place for fastening the tape so that it does not interfere with the closing of the window. The plastic surface is degreased, after which glue is applied and one strip of tape for fastening is glued. Now it remains to wait until the glue dries.

In the meantime, you can start making the insect net itself. The desired size is determined by measuring the diameter of the window with a tape measure. The mesh is cut to a specific size. The second part of the tape is sewn to the mesh around the perimeter, as shown in the photo. After the glue has hardened, you can begin to install the mesh on the window.

Video about a simple way to make a mosquito net:

Making mosquito nets with your own hands: choosing a canvas

The canvas is one of the main details of any mosquito net. In stores, the choice is simply huge and it is easy to make a mistake when buying. If you purchase material with the wrong cell size, you can completely ruin the business on the very initial stage. What to look for when choosing optimal view material? To buy a quality mosquito net, you should pay attention to the following parameters:

• cell diameter;
• canvas density;
• material type.

Pet lovers are always worried that pets do not damage the mesh. In this case, it is worth purchasing a durable anti-cat material that will withstand the attacks of pets. by the most the best option mesh of increased strength will become polyester or fiberglass with polymer coated capable of withstanding additional loads.

There are canvas options that are ideal for protecting the room not only from insects, but also from street dust and rain. In addition to the fact that the cross section of the cells in such nets is only 0.25x1 mm, it is additionally equipped with threads. However, it should be borne in mind that the smaller the cell diameter, the less air will enter the room.

Making mosquito nets with your own hands: installation rules

Starting the installation of a mosquito net, it is necessary to thoroughly clean the window frame from dust. After that, it is recommended to degrease the profile. For this, do not use caustic liquids, such as alcohol, thinner, acetone. Enough soap solution and then wipe the frame dry with microfiber.

Installation of mosquito nets is carried out on special fasteners installed in the corners. It should be noted that the lower fasteners have smaller grooves than the upper ones. Thanks to this, the frame of the mosquito net will be securely fastened.

When buying a canvas for a mosquito net, you need to consider the diameter of the cells

Fasteners are screwed onto self-tapping screws, and the seams are sealed with silicone. Thanks to silicone, rainwater and air will not penetrate inside the window frame. After screwing the lower brackets, a mosquito net is inserted into them and the upper fasteners are marked. The principle of installing a mosquito net on a plastic window is simple. At the beginning, the grid frame is wound up by the upper brackets until it stops. Then pressed firmly against window frame and run on the bottom brackets.

Installing a mosquito net on a plastic window with your own hands is a fairly simple procedure, especially if you prepare for these steps in advance. It is clear that without suitable tools just not enough. If you do this work yourself, you will be able to save a lot of money from the family budget.

The simplest is independent production mosquito net with suitable fine mesh material and adhesive tape for fastening. Such a product will provide protection for the premises for several seasons.

You will need the following components, which can be purchased at retail:

• mosquito net with 1.2 mm cells;
• adhesive tape - one side of it should contain a pile, and on the other there should be many small hooks;
• glue for gluing cork or mosaic.

Surface preparation

Mosquito net for plastic windows should be installed on a clean, prepared surface. The space is prepared by clearing open windows from dirt and degreasing their inner surface. To do this, you can use a soapy sponge, after wiping with clean gauze.

Considering that the installation is carried out on plastic windows be sure to use only soapy water for cleaning and never use solvents or alcohols.

Tape laying

After cleaning the surface, peel off the adhesive tape. Select the part with the hooks and glue to the perimeter of the window opening with the adhesive applied on the reverse side. Pay attention to the fact that the tape does not interfere with the closing of the window. It is very important that it does not create difficulties in the joint area between the base of the window and the side where it closes.

The tape can be glued more easily if you do the opposite, apply glue around the entire perimeter of the desired area, and then, without making extra measurements, cut the tape to the required length and width.

Markup and installation

Leave the tape for a while to dry, and start marking the mosquito net. Having measured the perimeter of the opening, and apply its contour to the canvas. When cutting, leave a margin that will be equal to the width. You need to bend the overlap around the perimeter, and then sew the second part of the tape, and with the pile out. Sew along the edge, if necessary, you can make additional stitches in the middle. After the tape with hooks is glued to the frame, wait about three hours. Then attach a mesh with a fleecy tape to it. Now you know that it is not so difficult to make this design with your own hands.

Installation of a mosquito net on a frame

Of course, the next option is not the cheapest. However, costs can be minimized if installation on plastic windows is carried out independently.

Materials. You need to purchase: metal corners, the width of which is about 1 cm, a plastic cable channel measuring 15x10 mm, glue, about sixteen rivets, the canvas itself of the right size.

Frame manufacturing

Since this kind of product is installed outside the window, when taking your measurements, focus on this side of the window. After the necessary data has been received, you can begin to manufacture the future frame: mark your received data on the cable and cut the required length at forty-five degrees with a saw cut with a file or knife.

The places where the cut was made, sand with a special whetstone. Compare the finished polished components of the future frame, connect metal corners. While holding them, make holes for the rivet in the finished cable channel, taking into account the holes in the metal corners.

Insert rivets into the holes obtained. It is important that the riveter is on the outside of your cable, not inside. If you don't have a riveter, you can use screws and nuts.

After tightening the screws, be sure to cover the nut oil paint to avoid screwing the nut during vibration.

Attaching the canvas to the frame

Having completed the frame, proceed to attaching your mosquito net to it. It is better to use a thin mesh to avoid the difficulty of pinching it in the cable. Lay it on top of the frame so that the edges protrude 2-3 cm beyond the perimeter of the frame, and snap the mesh with the cable channel cover, alternating snapping the short and long sides. Be careful before you fasten the long side.

Be sure to pull it up a little towards the corner to eliminate sagging - but don't pull it too hard, as this can tear the protective sheet. After you finish installing it on the frame, you can trim off any unnecessary sticking out excess. In some locations, apply adhesive between the cable and the cover to prevent spontaneous opening of the cover.

How to install ready-made in a window opening

From a sheet of metal, cut two strips of 20-30 and 20x40 mm, bending them into a Z shape. Try to make the bend wrap around the channel. Choose a shorter side where you drill a hole intended for a self-tapping screw. Ready-made fasteners are installed on the street side of the window, retreating about a centimeter from the window opening.

Fasteners are installed using a self-tapping screw, with long fasteners placed at the top, and short ones at the bottom. The distance between the lower and upper fasteners must exceed the length of the frame by 1 cm. Start the installation with the upper fasteners and end with the lower ones.

Intrusive insects interfere with living and sleeping peacefully at night in the warm season. They fly into the house through open windows. Despite the presence of a large number of special sprays and electric mosquito traps, only a mosquito net can significantly reduce the number of insects. Today, when replacing windows, you can additionally order this element, which costs money. How to solve the problem in the budget version? In fact, everything is very simple, since a do-it-yourself mosquito net is mounted very quickly from available materials.

Protective nets

Before heading to the hardware store for everyone necessary components, you should decide on the type of grid. All of them differ in different parameters:

1. By type of attachment: hooks, Velcro, pins and Z-brackets.
2. By type of opening: stationary, removable, sliding and roll.
3. By the presence of a frame: frame and frameless.
4. According to the place of attachment: internal and external.

Each of these types has its own advantages and disadvantages, but also disadvantages. All this is important to consider in order to right choice and don't waste your money. Special attention is given to the method of attachment, so let's figure it out: what are the pros and cons?

1. The frame is very rigid, because it is made of metal with a mesh cloth. It can be installed both on plastic and wooden windows from any side.
2. Sliding mount is only suitable for aluminum windows, as sliding doors will be used.
3. A mosquito net with magnets is a very relevant option for those who want to quickly get rid of insects. It attaches to both windows and doors. IN last case you don’t have to worry about the traffic, as the curtains are easy to open and close instantly.
4. Rolled nets will allow you to lead effective fight with mosquitoes. The material can be easily rolled up and unfolded from a cassette placed above the window.
5. The simple Velcro fasteners are also easy to attach and remove. At the same time, the mesh can be washed in the washing machine at any time.

Mosquito nets are installed not only on windows, but also on doors, as mosquitoes and midges also penetrate through them.

Canvas selection

The main element of any mosquito net is the canvas. You can buy it at any hardware store by the footage or in a roll (about 30 m). If you need to make only a couple of nets, then it is better not to spend money and buy the required number of meters. For more protective nets worth comparing prices: they may differ per square and per running meter s.

If we talk about quality, then it is important to consider several parameters:

• cell size;
• web thickness;
• material type;
• strength.

To create an anti-cat net, the strength parameter is very important, since it must withstand all the “attacks” of pets. by the most ideal option for this will be polyester with special impregnation. Additional fasteners are also required. It is especially important to install such mosquito nets on the balcony.

When determining the size of the cells, the size of the insects in the area from which additional protection is required should be taken into account. Minimum size section is 0.25×1 mm. Such a mesh can become a reliable protector not only from mosquitoes and flies, but even from sand, poplar fluff and dust. To protect windows and the room from rain, experts recommend a section of 1 × 1 mm.

Having decided on the materials and making necessary purchases you can start making. How to make a mosquito net for a frame and frameless window yourself will be discussed below. The protection will be as functional as it was from production.

The material from which it is made will be responsible for the quality of the protective mesh. Recently, polymer-coated fiberglass has become the most popular.

Manufacturing of frameless mesh

This is the simplest and a budget option, which will allow you to make a removable mosquito net, spending little money. The easiest way to make the protection stationary is to glue the canvas to the window frame. To make it better fixed at the edges, a tape of material with high adhesion properties is sewn on. When it comes to wooden windows, ordinary pushpins can act as additional fasteners. There is one significant drawback here - such a mesh cannot be removed for washing.

It is better to put a little more money and effort to get universal protection. It's about about Velcro mesh. To make it yourself, you will need the following materials:

• anti-mosquito material according to the size of the window;
• Velcro tape (burdock - one side with a pile, the other with hooks);
• construction adhesive.

Measurements are taken along the inner (opening) part of the window with a margin of 1 cm on each side. This size is necessary to fix the future mosquito net. One part of the adhesive tape is fixed around the perimeter of the window using building glue (for example, Titanium) or a simple double sided tape. The second is sewn around the entire perimeter of the mesh. When everything is ready and the glue is completely dry, you can fix the protective sheet.

The whole process of work takes a maximum of 2 hours, and as a result, everyone receives reliable protection from insects.

Before gluing Velcro to plastic, it should be thoroughly washed and degreased with alcohol.

Fabrication of a frame type mesh

Unlike the previous method, it is somewhat more complicated, but still everyone can handle it. It should be noted that this option is also suitable for the manufacture of mosquito nets on the door. So, for mounting the frame with your own hands, you will need the following components:

• cable channel rectangular section 15 × 10 cm (the length is determined independently based on the outer parameters of the frame, where the frame will be fixed);
• metal corners 10 mm - 4 pcs.;
• blind rivets - 16 pcs.;
• thin nylon mesh;
• construction adhesive.

Tools:

• whetstone;
• pencil;
• scissors;
• roulette.

We turn to the construction of the structure:

1. We measure the outer side of the window opening. Based on the data received, a frame will be made.
2. Celebrate on plastic box length and width.
3. Using a knife, cut off the vertical and horizontal parts at an angle of 45 °. The places of cuts are carefully polished with a whetstone.
4. We assemble the structure: we fix the corners with special connecting metal corners with rivets (nuts and screws are also suitable).
5. We apply a mosquito net with an allowance of 2 cm on each side.
6. In the upper part, we clamp the canvas with the cover of the plastic cable channel. In the process of snapping, we change the long and short sides. For reliability, some places are glued with glue.
7. Cut off excess fabric with scissors.

The finished mosquito net is installed in the window opening using Z-shaped brackets.

And this is how a grid is assembled from a special profile:

Restoration of mosquito nets

Not less than important process is the restoration, which includes the following main stages:

• Removing the frame from the brackets.
• Cleaning from dust and dirt.
• Removal of damaged capron.
• Installation of the repaired mesh in the window opening.

Before replacing any element in the structure, it is necessary to pay attention to how it is fixed and whether it can be removed. Most of the elements on the mosquito net from the manufacturer are fixed with a special sealing cord. If you carefully remove it, the holders will easily be removed.

All repair work carried out very carefully. It is important to remember that you are working with a fragile structure.

As you can see, in order to make a mosquito net with your own hands, you will have to spend 2 or even 3 times less than when ordering a similar design from the manufacturer. In addition, the installation process is quite simple, does not require special knowledge and equipment.

Video

See below the instructions for making a mosquito net for plastic windows:

You can do without making a frame, if you act like this:

Effective mosquito repellant and other small insects- mosquito net. You can buy a ready-made design, or you can make it yourself. Application modern materials allows you to make mosquito protection for the window from a mesh material that will fit snugly against the window frame and have a neat appearance.

Types of protective mesh

Before starting production, you need to decide what type of mesh you need. They differ in various ways:

• by type of fastening - on hooks, on Velcro, on pins, on Z-shaped brackets;
• by type of opening: stationary, removable, sliding, roll;
• by the presence of a frame: on a frame (frame), frameless;
• at the place of attachment: internal or external.

Below it will be described how to make frameless - stationary and removable, as well as a mosquito protection option - a mesh on a cable channel frame.

How to make a budget version of a frameless mesh?

The simplest version of a do-it-yourself frameless mesh is stationary. The canvas is simply glued to the window frame. But since the canvas itself does not hold well, a strip of material with good adhesion must first be sewn along its perimeter. It can be any fabric tape. If you are installing on wooden window, the canvas can be additionally fixed with buttons. The advantage of this method is maximum simplicity, the disadvantage is that the mesh cannot be opened or removed to be cleaned of contaminants. That is, after a while it will have to be dismantled and the whole procedure to be performed again.

The second option is Velcro mesh. In order to make it yourself, you will need the following materials:

• anti-mosquito cloth;
• Velcro tape (velcro, "burdock");
• construction adhesive.

Part of the tape is attached with construction adhesive to the inner quarter. That is, to that part of the frame to which the window sash adjoins when closing. The second part is sewn along the perimeter of the mosquito net. Before applying the adhesive, the section of the frame on which the adhesive will be applied must be degreased and cleaned of dust. The advantages of this type of frameless mesh are “reusability”, if necessary, it can be slightly opened or completely removed. In terms of cost, it also refers to the budget option.

To attach the Velcro to the frame, it is better to choose a transparent rubber adhesive, such as Tytan, which is then easily removed without residue. This is especially important if the window is plastic - overwriting and repainting like a wooden one will not work here.

Do-it-yourself frame-type construction

To make a frame with your own hands, you will need the following elements.

• Rectangular cable channel (15×10 mm). The length is determined based on the outer perimeter of the frame, where the frame will be attached.
• Metal corners (10 mm) - 4 pcs.
• Blind rivets - 16 pcs.

Related article: Creating an interior: how to choose furniture for wallpaper?

Of the tools you will need a saw for metal and a drill. First of all, the dimensions are taken - height and width. From the cable channel we cut 4 pieces at an angle of 45 degrees and fold in the form of a rectangle. Having put the corners on top, you need to drill holes in the profile so that they exactly match the holes in the corners. Then, with the help of rivets, the structure is connected - and the frame is ready. Please note that when riveting, the riveter must be located outside the cable channel.

After the frame is ready, you need to fix the canvas in it. It is superimposed over the frame and snaps into place with the cover of the cable channel. To fix it evenly, without sagging, you need to start fastening along one of the long sides. At the same time, you need to make sure that there is no distortion. Then the canvas is fixed on one of following parties frame.

It is better to fix the opposite sides with an assistant, as here you will need to provide light tension. At the same time, stretching the canvas, making sure that there is no skew and snapping the bar is inconvenient, so an extra pair of hands will come in handy here. Frame type mosquito net can be attached to the window different ways. The most common is plunger, using Z-brackets.

To avoid snapping the bar, it is better to additionally fix it with glue. To do this, when the design is completely ready, a small amount of glue must be applied to the gap between the cable channel and its cover (bar).

How to choose a canvas?

The main element in any such design is the canvas. It is sold in rolls and by the meter. There are about 30 meters per roll. If you need to make 1-2 designs with your own hands, then it is better to buy by the footage. When comparing prices, please note: they can be indicated both per square meter and per linear meter. In terms of quality, the canvas differs in the following parameters:

• cell size;
• web thickness;
• material;
• strength.