• Repair
• Repair
• Interior Design
• About everything
• About plumbing

Technoelast laying technology. Technoelast epp - roofing waterproofing material. Roof quality control. acceptance rules

Technoelast– SBS-modified* roll roofing and waterproofing material increased reliability.

Technoelast fabric consists of a synthetic non-woven base (polyester or fiberglass) coated on both sides with a bitumen-polymer binder containing a polymer modifier.

Appointment. Installation of a waterproofing membrane for concrete and reinforced concrete bases (foundations, basements, tunnels, garages) and waterproofing flat roof to protect against negative impact moisture.

Technoelast waterproofing retains its consumer properties during operation in a wide range of temperature fluctuations, withstands high mechanical loads.

The use of this roofing and hydro insulating material, will allow to form a reliable, biostable and durable waterproofing carpet with large stock strength.

The inclusion of polymer additives in the production of rolled waterproofing materials increases their flexibility and heat resistance, protects the bitumen cover layer from aging, destruction and roof leaks.

On rolled materials produced with the use of polymer additives, the protective coating adheres much better, which gives additional protection to the waterproofing carpet from overheating and the damaging effects of UV rays during the operation of a flat roof.

Therefore, a roofing waterproofing carpet based on bitumen-polymer materials has a significantly longer service life than those made from materials based on oxidized bitumen.

The logo printed on protective film, on inside the web of the roll is used as an additional indicator indicating the sufficiency of the degree of heating of the casing bitumen.

Technoelast roofing material can be used in all climatic zones of Russia.

Depending on the scope of application of the rolled waterproofing material, two main types of Technoelast have been developed:

1. Technoelast P- used as the bottom layer of the roofing carpet and waterproofing of building structures. The upper and lower (surfacing) layers of the web are covered with a polymer film that prevents it from sticking when stored in a roll. TO this species applies: technoelast HPP, technoelast EPP.
2. Technoelast K- used for the installation of the top layer of a waterproofing roofing carpet. The outer side of the web of the roll is covered with a protective dressing to protect the top layer layer from the negative effects of various atmospheric phenomena and exposure to UV rays. Inner - protective film. This type includes: technoelast TKP, technoelast EKP.

Technical characteristics of Technoelast

Technoelast laying. Sheets of material are welded onto a previously prepared and primed base of a flat roof, foundation, basement, building structures made of concrete using a gas burner. Read more about laying bituminous weld materials.

Quick Guide preparing the base of a flat roof for laying roll waterproofing, read .

Below is the installation of roof waterproofing from the company TechnoNIKOL, which shows the main stages of the installation of a waterproofing carpet from welded materials.

Potential lifetime of the material. The potential durability of the material, according to the test protocol, is 25-30 years. The degree of wear of the material after five years of operation is only 22%, and the appearance of the first leaks due to wear of the material is only after 18 years of operation.

The main scope of Technoelast rolled waterproofing material:

• waterproofing of the foundation, basement, building structures, reinforced concrete floors and other bases made of concrete (Technoelast HPP, EPP);
• bottom layer when installing a two-layer roofing flat roofs, including those on the base of a prefabricated screed (Technoelast HPP, EPP);
• the top layer when installing a new or repairing an existing flat roof waterproofing carpet (Technoelast TKP, EKP);
• additional reinforcing layer when arranging connections to vertical surfaces: parapets, walls, technical structures(Technoelast HPP, EPP).

Advantages of using Technoelast material:

• high reliability;
• long service life - 30 years;
• versatility - the ability to use on various operational grounds and temperature conditions;
• elasticity of the material low temperatures- easy to fit in winter time. Allows for waterproofing works in different seasons of the year. Application temperature up to -30°С;
• low maintenance costs of the roof. Despite the higher basic cost of roofing, the cost of restoring a roof made of bitumen-polymer materials will cost almost two times cheaper (53%) than repairing a roof made of bitumen materials on oxidized bitumen;
• high standards production and Hi-tech the leading manufacturer of rolled waterproofing in Russia.

Price. You can find out the current prices for the material and buy Technoelast by calling the contact number. The price of Technoelast material per 1 m2 depends on the scope of supply.

IN modern construction Increasingly, new types of materials with improved technical specifications. One of these innovations is technoelast, which is produced by the Russian corporation TechnoNIKOL.

What it is?

Technoelast is a multifunctional bioresistant roofing and waterproofing material high quality and increased reliability. It is manufactured using a unique technology by applying a special insulating compound (bitumen, SBS thermoplastic or its modifications and filler) on a fiberglass or polyester base on both sides.

SBS (styrene-butadiene-styrene) is a polymer, styrene-butadiene thermoplastic elastomer, better known to everyone as artificial rubber (it is this that provides high elasticity to the web, preventing cracking at low temperatures).

As a filler, talc, dolomite and other materials are used. The surface protective layer consists of coarse or fine-grained mineral dressing (sand, etc.) and a polymer film.

Application

Waterproofing Technoelast is designed for waterproofing any building elements of structures (floors, walls, channels, mounting joints), surfaces that are constantly in contact with water (pools, foundations, basements), all types of roofs (non-exploited, "green" - with gardening, with increased load in use, etc.).

It provides 100% protection against moisture, condensation, gases and steam in any climatic conditions, taking into account the requirements of SNiP 23-01-99.

Types and brands, specifications

The insulator has several versions, depending on the conditions and application. Abbreviation:

• the first letter (the basis of the canvas) - ether (polyester), canvas, fabric;
• second, third letters (protective layer):
  • P (for the lower layers of the roof sheet, fine-grained dressing, polymer film or a combination of them is used);
  • K (for upper layers"carpet" of the roof, contains a coarse-grained dressing on the front side and a film, or a fine-grained mineral fraction on the side of the overlay).

Technoelast EPP (polyester+film+film)

Used for waterproofing the foundations of buildings and other elements of building structures, as roofing material V various types buildings. Provides reliable protection from water, absolutely waterproof, has good performance heat resistance, high elasticity provides greater convenience in work.

It consists of a fiberglass or polyester base, bitumen mixed with polymer additives (SBS thermoplastic), filler. The cloth has the protective layer consisting of fine-grained dressing and a polymeric film. The insulator is fastened by welding using a gas burner.

Technoelast EKP (polyester + crumb + film)

It is used as the top layer of roofing, for waterproofing basements. Differs in cold resistance, does not crack even when severe frosts. The total thickness of the material is 4.2 mm. The base is a durable non-rotting polyester, on which a layer of bitumen with a thermoplastic is applied, at the bottom is a mineral dressing, consisting of large fractions and reducing the negative effect external environment. On top - a protective synthetic film.

Technoelast HPP (canvas+film+film)

It can be used for waterproofing various sections of buildings and as the bottom (lining) layer of the roofing sheet. Frost-resistant and heat-resistant material. It is a compressed fiberglass coated on all sides with a layer of bitumen with SBS polymer additives, with a protective film that serves as an indicator during welding, prevents the web from sticking.

It does not contain polyester and mineral chips, therefore it has a small thickness (3 mm), suitable for surfaces with low loads.

Technoelast EMP (ether+fine dressing+film)

Durable bio-resistant material, designed for waterproofing building elements (including roofs) and reinforced concrete deck (roadway) of bridges. It consists of a polyester base, bitumen mixed with a polymer modifier, mineral filler (dolomite, talc, etc.) and an outer coating made of fine sand and polymer film. It has a low level of water absorption.

Technoelast TKP (fabric + crumb + film)

It is used for waterproofing underground sections of buildings (basements, foundations), when arranging the upper layers of coatings (flat and pitched roofs), can completely replace the roofing "carpet".

Durable, durable coating mechanical damage, provides protection against water, often used as a vapor barrier. Provides a perfectly even smooth canvas.

The basis is fiberglass, which is covered with a layer of bitumen with SBS modifier. External protection consists of mineral dressing and film. The thickness of the material is 4.2 mm.

Technoelast Alpha

Designed for hydro- and gas protection of underground elements of building structures. A feature of this insulating material is the presence of a metal foil in its composition, which protects underground rooms from dangerous inert gases - radioactive radon, methane.

Technoelast Alpha consists of several layers. Inner part made of polyester and an aluminum gas barrier, followed by double-sided application of a bitumen-polymer composition, filler and a protective film of polymers. The 4 mm thick multi-layer construction has a high level of protection and can be used as a vapor barrier. Dimensions: 10x1 m.

Technoelast Barrier (BO)

Waterproofing material with self-adhesive surface. It is intended for protection of internal and external elements of buildings. Consists of 1.5 mm polymer film coated with bitumen and thermoplastic. The upper part is a silicone coating that can be easily removed.

BO means "without base". The absence of a base allows you to achieve high elasticity and flexibility of the material. The special adhesive composition applied to the bottom of the sheet provides reliable adhesion to concrete or metal surface, so no additional base is required.

Can be laid on combustible elements ( high level fire resistance). At a temperature vertical surfaces above +85°C it is not recommended to use it (may come off). When working, it must be borne in mind that the temperature of the surfaces during gluing should be + 5 ° C, otherwise heating of both the base and the web itself will be required. Dimensions: 20x1 m.

The material is supplied in two versions: Technoelast Barrier (BO) and Technoelast BARRIER (BO) - MINI). "MINI" is distinguished by a smaller width of the canvas. Thanks to small size provides greater ease of use and wide application. It becomes possible to use a waterproofing agent when working in a limited space, to protect small construction and technical elements structures (sealing pipes, seams, joints, etc.). Dimensions: 20x0.2-0.25 m.

Technoelast Barrier Light

Self-adhesive insulating material intended for use in indoor areas- another modification of Technoelast BARRIER (BO). Has all the benefits of this series protective materials: high elasticity, high flexibility and wide range of use.

It has an additional top coating of non-woven fabric (polypropylene spunbond), which can be subsequently applied to any decorative elements without the device of an additional layer (fastening over the waterproofing). Dimensions: 20x1 m.

Technoelast GREEN

A special type of waterproofing material designed for highly effective chemical and mechanical protection of building structures, including when installing a "green roof".

The roofs of modern urban buildings today perform not only a protective function, they often represent complex structures With big set design elements, arrangement of recreation areas, planting green spaces. "Green roofs" require a special approach when installing waterproofing. Provision should be made for protection against micro-organisms, chemical substances used in the care of plants, the destructive action of the root system.

"Green" consists of a polyester base, on which bitumen with polymeric thermoplastic elastomer, filler, anti-root additives are applied from 2 sides. From above, the canvas is covered with a protective layer consisting of coarse or fine-grained sand and a film. Fire resistant material.

It is produced in two versions: Technoelast GREEN EPP (the upper part is a film) and Technoelast GREEN ECP (a thicker protective layer is 4.2 mm, the top is slate). Dimensions: 10x1 m.

Technoelast ACOUSTIC

It is used as a hydro and sound insulating element in building structures, including when installing floating floors. Significantly reduces exposure impact noise(by 21–26 dB).

The base consists of soundproof fiberglass, on which a bitumen-polymer layer is applied. The canvas is laid end-to-end (soundproofing layer - from the side of the base), taking into account the height of the finish coating, fastened with adhesive tape.

Technoelast ACOUSTIC is produced by applying bitumen with polymer inclusions to the surface of the fiberglass and, additionally, soundproof geotextile. The top layer is film. Dimensions: length / width - 15x1 m, thickness - 2.5 or 4.8 mm.

The material is produced in two versions: Technoelast ACOUSTIC (thickness - 2.5 mm), Technoelast ACOUSTIC-SUPER (differs in a larger web thickness, since the bitumen-polymer composition is applied on both sides).

Technoelast SOLO

material with wide colors, with a coarse-grained top layer and a non-woven fabric underneath. It is used as a waterproofing and in the design of a single-layer roofing. Easy to use, indispensable in cases where simple mechanical fixation is required, laying on a layer of mastic.

It can be applied to the substrate by partial fusing. Has improved fire performance, refers to moderately flammable materials, almost does not spread the flame.

It consists of a polyester base, on which a binder composition of bitumen and polymeric SBS is fixed on both sides, on top - a mineral filler (talc, dolomite, etc.) with the addition of flame retardants. The upper protective layer consists of a coarse-grained dressing (gray slate, aluminized slate, basalt), the lower one is made of a non-woven fabric or film.

The wide edge-overlap on the sides (1-1.2 cm) is covered with fusible material or non-woven fabric for convenience. Can be glued on a base covered with mastic, mechanically or by welding, using automatic equipment. Edges must be carefully sealed to ensure tightness. The material is very durable, the waterproofing layer is 5 mm. Canvas dimensions: 8x1 m.

Technoelast FIX

It is applied at the device of the bottom layer of a roofing covering. used mechanical system fastenings, with subsequent processing of seams gas burner. This method can significantly reduce the time of work, provides a free fit of the material to the base.

Work is carried out on the principle of "breathing roof". Laying on combustible bases and any types of insulation is possible, on a roof with a large slope (up to 100%).

Two-layer material: top layer - Technoelast EKP, lower - Technoelast FIX, which was developed specifically for roofing with mechanical fastening. Reinforced non-rotting base made of polyester and coated on both sides with a layer of bitumen mixed with SBS polymers allows avoiding deformation.

Coarse sand in the outer (lower) part of the canvas does not allow the material to stick to the base. Polymer film at the top provides additional protection. Dimensions: 10x1 m.

Underground or underwater structures, foundations. Can be used in absolutely any corner Russian Federation, as it has excellent low-temperature characteristics.

Technoelast is multifunctional, SBS-modified, it is undoubtedly one of the leaders in terms of reliability and durability.

Technoelast production

A polymer-bitumen binder is applied to a polyester or fiberglass base. It consists of bitumen, filler and technological additives.

Thus, a multilayer material is formed, where there is necessarily a base in the middle, coated on both sides with a bitumen-polymer mixture.

Along the edges are the upper and lower protective layers, which are used as a polymer film and coarse-grained and fine-grained dressings.

The constituent components and the final result of the manufactured product may differ depending on the modification.

In case of violation of the technology of production and storage of technoelast, the dressing may crumble, the insulating properties of the material may be violated.

Technoelast refers to waterproofing and roofing roll materials increased reliability. It is applicable in construction in almost any climatic conditions (including in the far north).

Technoelast: the main brands that distinguish them

Depending on the scope, protective dressing and base component, there are such grades of Technoelast material:

1. EPP - polyester base, polymer film as protective layers. The 4mm material ensures reliability and confidence even in adverse conditions. chemical conditions. The achieved strength, elasticity and durability make Technoelast EPP a premium class material.
2. EKP - the basis for this brand is a non-woven polyester fabric with a coarse-grained mineral dressing and a protective polymer film. Technoelast EKP is very popular and is used for facilities in increased requirements- Bridges, tunnels.
3. TKP - frame fiberglass with coarse-grained dressing and polymer film. Due to its high tensile strength (not less than 800/900 N/mm), Technoelast TKP is used on loaded surfaces.
4. HPP - the reinforcing basis of the material - fiberglass, the protection is a polymer film. The small thickness and manufacturing technique do not allow the use of Technoelast on surfaces that are subjected to loads.

Technoelast: work technology

Technoelast is easy to install, does not require additional equipment and can be produced in a limited or enclosed space. Removed from the material protective film, laid on the prepared surface and rolled with a roller so that it sticks. Optimum temperature laying is more than five degrees, otherwise the room or the base is heated.

Probably the only drawback of the Technoelast material is its price. But quality doesn't come cheap. And after a couple of years of service, each consumer understands that he once made the right choice.

In order for the roof to serve for a long time, it is required to technologically correctly perform roofing. Regardless of whether the laying of Technoelast will be carried out by you personally or by a construction company, you will need the following necessary minimum of knowledge

The secret of fast laying Technoelast

Surface preparation